Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Nail Gun 101

Posts

Nail Gun 101

#1

Nail Gun 101

David Charters Durham NC

>Hi all, I have been looking through the archives and wherever I can to find out more about nailers and air compressors. I have never used one, but I have a house full of molding to put up and thought it would be a good reason for a new tool. I also an about to build a big fence and thought it might be helpful there too. Amazon has a Porter Cable set with a brad nailer, a finish nailer and a stapler with the compressor $280 http://www.amazon.com/Porter-Cable-CFNBNS-Nailer-Compressor/dp/B000HZGTIA/ref=sr_1_7?ie=UTF8&s=hi&qid=1202004712&sr=1-7

would I really need all three of these or do I just really need something for small nails and something for large nails?

What's up with Campbell Hausfeld? Any good? Any other sets people like or advise. I am willing to kick down now for decent tools, but I am not sure what to get. I'd like a compressor I won't grow out of, but also one I can tote around somewhat easily (won't be doing any spray finishing though I think). Well any advise would be great, I know these questions are kinda vague but that's where I am at.

Thanks,

David

Re: Nail Gun 101

#2

Re: Nail Gun 101

Nat Robison

>I own one of the P-C combo kits with 16 ga. and 18 ga. nailers. They've been great so far for use around the house. No probs with either gun. Doing trim is definitely a lot more enjoyable.

The compressor is LOUD but easy to transport between the basement and garage when necessary.

Re: Nail Gun 101

#3

Re: Nail Gun 101

David Charters Durham NC

>Are they different enough that you are glad you have both of them? What do you use each for?

Thanks, David

Re: Nail Gun 101

#4

Re: Nail Gun 101

Nat Robison

>It basically depends on what you're nailing and nailing into. The 18 ga. nailer generally has 1 1/4" nails in it and would use it for attaching a crown or cove molding to a piece of furniture, pretty much anywhere where I don't want the nail blowing through the backside of the casework. The 16 ga. nailer has 2" nails in it and would be used for baseboards and anywhere the nails could seat fully.

I'm by no means an expert on nailers and these are my first air-driven nailers and compressor. That being said, I'm glad I have both and they've worked very well for my homeowner use.

Re: Nail Gun 101

#5

Re: Nail Gun 101

Tom

>I know conventional wisdom is to use the 16 ga. for baseboards. I have one, as well as a few 18 ga. brad nailers. I almost always use the 18 ga for baseboards, however. As long as it's going into a stud, I've never had a problem with the baseboard coming loose. It leaves a lot smaller hole too. I did make sure to buy a brad nailer that takes really long (2", maybe a bit longer?) brads.

Re: Nail Gun 101

#6

Re: Nail Gun 101

ScottS

>I bought the P-C kit that includes an 18ga brad nailer and a 16ga finish nailer. I almost never use it. The compressor is so damned loud that even with a 50ft hose attached, I can't get it far enough away that it doesn't bug the crap out of me. Wish I'd bought a quieter oil-lube compressor.

When I do bother to fire up the compressor, it's almost always connected to my Grex 23ga headless pinner. I bought the P635, which seems to work very well for the simple crown molding, baseboards, and other trim my house uses. If the P645 (=1.75in max) or P650 (=2in max) were around when I bought, I'd probably have purchased one of those instead. The headless pins seem to have pretty decent holding power (when fired in a 'V' pattern) and the holes they create are significantly smaller than an 18ga brad.

Re: Nail Gun 101

#7

Re: Nail Gun 101

Dave Bair, Eaton Rapids, MI

>I have all three of the nailers you are considering.

The brad nailer is useful for trim work, especially that which won't be painted.

The finish nailer is reserved for door frames and situations where I need a stronger mechanical connection, like the fence you mentioned, and shop jigs.

The stapler is used to attach plywood backs to cabinets and also used for stapling carpet down next to hardwood flooring and onto stair treads. I've also used it to construct small cages using hardware cloth.

I picked up a small Delta compressor for $99 that is much quieter than my defunct pancake and light enough to haul anywhere one-handed.

Re: Nail Gun 101

#8

Types & Uses for nailers

Derek

>David,

There are a number of nailers to choose from. Each has it's intended purpose and some will be useful for more than one, but none are useful for all.

I am not an expert but I have used all I list below except roofing and 16 gauge nailers. There are others than what I list below, but these are the ones which are generally used. Different nailers of a given type have slightly different capabilities (such as length of nails allowed). Some nailers need nails which are hard to get - consider this before purchasing.

Framing nailer - for framing and heavy work. This is what you would generally need for a normal fence.

Roofing nailer - kinda obvious what these are for. These generally shoot shorter nails with bigger heads than framing nailers.

15 gauge finish nailer - this is useful for hanging doors and baseboard and other finishing tasks. The nails are heavier than the 16-gauge ones and hold better. The magazine is angled so it is often easier to get into tight places in use than a 16 gauge unit.

16 gauge finish nailer - Same general use as a 5 gauge unit. I feel the nails are a bit light for some uses such as nailing in door frames.

18 gauge brad nailer - useful for light trim work and cabinet work such as nailing face frames onto carcases.

1/4" crown stapler - useful for nailing backs onto cabinets and other fastening which does not require long fasteners and where it will not show.

23 gauge pinner - very light duty nailer which is useful for thin moldings and very light work. The nails are headless and you must put them in at an angle for them to really hold anything. Usually the pins are used to hold light work in place until the glue dries.

As for compressors - I would not buy an oil-less one. They are louder and will not last as long as one with oil. I've seen oil units pretty cheap in the last year.

I hope this helps. Think of what you are going touse the nailer for and buy accordingly.

Re: Nail Gun 101

#9

Re: Nail Gun 101

David Charters

>Thanks for the advice and info everyone, I found the Porter Cable combo brad, finish, stapler and oilless compressor for $238 delivered so I went that way, I figure I can sell the compressor and trade up if it makes too much of a racket. It sure is going to be nice doing trim now, it's almost like cheating...

Thanks,

David