Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

OT - electrical wiring ?

Posts

OT - electrical wiring ?

#1

OT - electrical wiring ?

Mike Hamilton

>LOML has me swapping out medicine cabinets in one of our bathrooms. Turns out the point where the wiring for the over-cabinet light comes through the wall is coming down about 9 inches. The current wire misses being long enough to anchor in a new box by about 4 inches (assuming I want the full sheath to enter the box for clamping). I assume this kind of splice will need to be clamped inside a junction box.

If I'm wrong, stop me before I make this more complicated than it needs to be.

Expecting no help at the store, I turn to the collected wisdom and experience here.

Many thanks,

Mike Hamilton

Plainfield, IN

Re: OT - electrical wiring ?

#2

JL

Re: OT - electrical wiring ?

JL

>All junctions and splices should be in a junction box - an outlet box also counts.

Re: OT - electrical wiring ?

#3

Re: OT - electrical wiring ?

Bill Howatt

>And the junction box has to be accessible - no covering it over with drywall. Your best bet would be to make/buy some kind of a decorative cover.

Bill

Re: OT - electrical wiring ?

#4

Been there, Done that

Neal in San Jose

>If a decorative cover on a junction box doesn't work, I've done two fixes. If you have access to an attic or crawl space above the bathroom, you can pull the wire up and put the junction box up there. A second possibliliy is what is on the other side of the wall? If you are lucky and there is a closet, you can put the junction box flush to the wall there. It is fully accessable, just not in plain sight.

You REALLY don't want a splice that is not in a junction box. I ran into this one time when a friend's mother lost power in one circuit in her house. Turns out her son had put a splice behind a medicine cabinet, and over the years one of the wire nuts loosened up and the wires started to arc and finally burned in half. Luckily it didn't start a fire in the wall, but I still shudder to think of what could have happened. That was a bear to find, by the way.

Re: OT - electrical wiring ?

#5

Trick for Running New Line

Rick Christopherson

>Oh, before I start, Bill's advise is correct, and it is the basis for doing the following.

It is hard to tell from your description, but it sounds as though adding something to the bathroom will result in the wires being too short to reach their normal destination. That is a generic description, but it is very common. The problem is that you don't have wall access to string new wires, but the existing wires need to be lengthened or moved.

Before you pull out the existing wires, tie a string to the loose-end of the wire, such that when you pull this wire out of the wall back toward the original junction box, you also pull the string through the wall as well. Once the wire is removed, you now have a "fishing" string in place where you can use this for pulling new wire through the same holes.

This won't work for some long runs because the original cable may have passed through a cable clamp, but in many wall passages, this will let you re-fish a new wire without tearing out the wall. At worst, you could knock tiny holes in the walls to clear clamps or other minor obstructions.

Re: OT - electrical wiring ?

#6

Re: Thanks to all

Mike Hamilton

>I appreciate all the replies. When I cut open the wall, I found a staple I was able to loosen. Then I was able to pull up enough slack to keep from splicing. Hooray! One junction box at the light and a mess of wallboard work and we're there.

Again, thanks,

Mike

Re: OT - electrical wiring ?

#7

Re: OT - electrical wiring ?

Paul Leuba

>One option that was not mentioned by previous posts is to route the existing wire to a newly installed wall mounted receptical near the medicine cabinet. This would allow the installation and routing of a new wire from the newly installed receptical to the light fixture. Of course, the new receptical will only be "hot" when the light switch is in the on position.

Re: OT - electrical wiring ?

#8

Re: Thanks to all

Steve Roxberg

>To meet code doesn't the cable have to be stapled or held firm wihin 6" of entering a box? So if you removed the staple and didn't replace it haven't we created another code violation?