Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Nail Gun Question

Posts

Nail Gun Question

#1

Nail Gun Question

Ken Krawford

>I have a feeling the answer to my question is going to be the same as the proverbial "How do you get to Carnegie Hall?" question but here goes anyway.

I'm a relative newcomer to nail guns and find myself blowing a nail out the side of a board when end nailing. It occurs with both my 16 and 18G guns. The 16G had a bigger, flatter shoe but I still manage to misfire. I think the length of the fasteners are appropriate for the thickness of the stock.

Are there any pearls of wisdom that you could share to help me?

Re: Nail Gun Question

#2

Re: Nail Gun Question

Joseph Mulherin

>Lower the pressure going from the compressor to the nail gun.

Re: Nail Gun Question

#3

Re: Nail Gun Question

Stuart Hough

>Ken, not that I'm an expert, but when I got my 18g Bostich, I found that you really need to pay attention to the air pressure to make the depth guage work properly. I use 75 psi (on the low end of the range) and have no problems seating a nail fully. Next, you need to watch the angle with which you hold the gun. You need to have the gun lined up to the target properly. I'ts sorta like golf , the followthru is as important as the "swing". When the gun popped, I found that I had a tendency to ease up on my grip, and that allowed the gun to move slightly, causing the nail to bend slightly, which will cause the nail to swerve. Also, MOST important, is to look for any visible variations in the grain near your target, as these type of nails will follow the grain rather easily. Just my experiences. Hope it helps.

Re: Nail Gun Question

#4

Try 90 degree turn

Larry in SE MN

>Some or most of the nails are cut so they will follow growth rings in one position and cut through the rings if the gun is rotated a quarter turn left or right. In the first instance, the point of the nail is deflected enough to follow the ring "around" the tree. In the second, the nail point cuts straight ahead without deflection.

Try a couple of shots near the end of a piece of wood with pronounced grain to see which orientation gives the "following" action and which gives the "straight ahead" action.

All bets are off if nailing through particle board. Here you have to be lucky and watch your fingers. Nails sting a bit going in and hurt like H*LL coming out. DAMHIKT....

Re: Nail Gun Question

#5

Ditto

Grant Smith

>Ken,

Take a look at the nails in strip form and note that they are (usually) thicker in one dimension than the other. Further, the tips are (usually) chisel shaped.

Obviously, the nails will be more likely to bend left to right as they come out of the gun than front to rear. Therefore, hold the gun such that the gun is perpendicular to the important edge when nailing. Also note that in very hard or figured wood, or maybe the 200th odd nail, the nail will do the unexpected on its own regardless of how careful you are.

Also look at the grain in the end of the boards you are about to nail and invision the nail going through the growth rings. In most woods, the nails will tend to want to follow the rings, so situate your boards and aim the gun to compensate as much as possible.

Thicker nails will have less of a tendency to do this, though they still will.

As a side note, I have seen a 2 1/2" nail go in an apparently clear board, do a 180 and the end pop out an inch away from where it went in. If you shoot enough nails, you'll either nail yourself annually, or learn where not to put your hands.

regards,

Grant in Iowa<---with a chip in his glasses from an errant finish nail that went ballistic.

Re: Nail Gun Question

#6

Re: Ditto

Ken Krawford

>Most everything I'm working with on this project is plywood. I assume there is no way to predict a nail path with this stuff.

Luckily this project is going to be painted. If I were to be stained, I'd have a mess!