Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Kerosene heaters and moisture???

Posts

Kerosene heaters and moisture???

#1

Kerosene heaters and moisture???

Brian in Sandusky, OH

>Do kerosene heaters put moisture into the air?

It's very dry here in northern Ohio (in spite of some recent rain), and I notice that my kerosene heaters seem to drive the humidity in the shop up. From about 25% relative humidity to about 45% rh.

This isn't a huge increase to where I'm concerned...I'm just curious.

I'm using two heaters....one is the "jet engine" forced air type, and the other is a radiant flame heater with a wick.

I use the forced air heater to quickly warm up the shop, and then the radiant flame heater to maintain the heat.

Thoughts?

Re: Kerosene heaters and moisture???

#2

Re: Kerosene heaters and moisture???

Clint Searl, at the base of Haycock Mtn

>Yes, the primary products of complete combustion are carbon dioxide and water. You might consider installing a carbon monoxide detector, as kero heaters are notorious for generating it.

Clint

Re: Kerosene heaters and moisture???

#3

Re: Kerosene heaters and moisture???

Barry Irby

>Clint nailed it. When you burn a hydro carbon fuel in air you water and carbon dioxide (Mostly) and some other minor but potentially harmful components. The CO detector is a good idea. If the unit is burning improperly it will produce CO and most of them burn poorly at sometime during their lives.

18% of what goes up the flue on gas furnaces is steam. The newer higher efficiency units condense the steam to get the heat and put it into your house rather than up the flue. An unvented heater dumps the steam in the living space, making it warmer and raising the humidity, often making it feel warmer, but potentially busting your tools.

As a Home Inspector, I have seen several houses with condensation drooling down cold walls and dripping fromt he ceiling because they were using a bunch of tiny kerosene or gas heaters.

Re: Kerosene heaters and moisture???

#4

Re: Kerosene heaters and moisture???

Lee Schierer - McKean, PA

>All portable heaters draw their compbustion air from the room they are in. In a closed space, they can quickly deplete the oxygen levels to a dangerous level. Fires will burn at a lower oxygen level than a human can breathe. CO monitors are a good idea. Vented heaters are a better idea.

Lee

Re: Kerosene heaters and moisture???

#5

Yes, too much moisture in my opinion...

Tim Greif - West of Chicago

>I lived with a torpedo kerosene heater in the garage shop for years. Never again. LOML always complained about the odor, but what she really hated was what the vapor did to her contact lenses. Went through them much more quickly when she spent any time in the shop with me.

The moisture was enough to cause any unprotected metal to rust. Think about how you use a space heater in a shop - probably imtermittently. If it was warm continuously, you probably wouldn't have a problem. But you go into a cold shop, fire up the heater and put a bunch of moisture into the air, which immediately begins condensing on the cold metal surfaces. Presto - we have rust developing. Never stops.

I switched to a gas unit heater and should have done so years ago. BTW, propane fired heaters are worse than kerosene units when it comes to moisture addition, from what I've been told.

Re: Kerosene heaters and moisture???

#6

Thanks everyone!

Brian in Sandusky, OH

>The kerosene heaters are only a temporary heat source as I have broken ground on my new shop.

Then it's a vented propane furnace.

Re: Kerosene heaters and moisture???

#7

Re: Thanks everyone!

john lucas

>Brian I've been using a kerosene heater my shop for years with no problems I can tell. It might add moisture but I don't notice it. At the present time Kerosene in 5 gallon quantities is less expensive than propane in 20 gallon tanks. When I can step up to 40 gallon it will be less expensive but that of course means I have to buy the tank so for now it's still Kerosene for me.

Re: Kerosene heaters and moisture???

#8

Re: New shop heat

Larry Clinton At Frankfort (Central)., Indiana

>Brian, I think the other posters have covered the kerosene heater issue. I would like to comment on the heat system you are installing in your new shop. I installed (and would advise you to investigate) a forced air direct vent furnace in a room over my shop. I had the trusses built for my shop with an opening 10' wide X 8'+ tall in the center - I do have "knee walls on each side (45 degree - side walls are about 5' high). The furnace pulls combustion air in from outside and vents back out - both though 2" PVC. I also installed central air at the same time. I installed a "drop" in my lower shop ceiling of about 6" deep about a foot from the outside wall so that I could run trunk the width of the shop under the upstairs floor. Then I attached trunk at right angles to the end of the primary trunk running the length of the shop about 4' from the walls. The 6 downstairs vents were installed about a foot from the outside wall, using the insulated flex 6" duct and ceiling registers. I did install one register upstairs. The return air is taken through a 20" X 20" filter grill in the shop ceiling. I drain the furnace air using a pvc pipe ran exposed on the inside wall then through the wall outside. (I do have some problems with this freezing so am installing it into a sump with insulated/ heat tape pipe next summer. This system (other than the drain freeze problem) has ran perfectly and keeps my 30 X 30' shop at a constant temp. both summer and winter, I have seen no "hot or cold" areas. I did super insulate the shop so have very low energy costs - estimate it costs less than $100 (coldest month in winter) and less than $40 (hottest month in summer) to keep the shop at 72 year around. As the combustion chamber is sealed, I have no concern about dust or finishing solvent issues. I installed HVAC as a side job for over 25 years, so designed & installed the system myself. I found a Payne furnace (97% efficient)and seer 10 air conditioning components at a local discount HVAC supplier. Cost for the Furnace and air was around $1500 - ducting etc. was around $1000. After installation I blew cellulose insulation over the ducting - filling the space completely. Even if you don't build with an upstairs room, you can install a horizontal furnace overhead (my furnace is a multi-position and can be installed as an updraft, downdraft or horizontal). If I can help in any way just email me.