Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Dust collector issue uncovered

Posts

Dust collector issue uncovered

#1

Dust collector issue uncovered

Pete in Holland, MI

>My Grizzly 2 hp dust collector system had been kinda weak for the past month. Started doing some diagnosis today looking for leaks. Pulled the Y-fitting off the blower intake and found a large piece of sandpaper covering most of the safety grill. This grill needs to be there to keep big stuff from sucking into the blower and making a mess of things.

Sandpaper was removed and system was back to normal.

Thought I'd pass this one on.......

Pete

Re: Dust collector issue uncovered

#2

Re: Dust collector issue uncovered

Barry Irby

>I have a Delta 1 1/2hp DC. It does not have any internal grill to prevent big stuff going through. Occasionally I suck up a small piece of scrap and I hear it tumble and rattle through the system and hit the impeller. Sometimes it hits the impeller two or three times before it makes it into the bag. I was wondering if I were the only one that enjoyed "pinging" the DC.

I have also sucked up plastic bags and string. Not good. Had to take the system apart to clean the out where they wrapped themselves around the impeller. (Take my advice, don't try it, you won't like it)

The thing I have done that improves mine or should I say revitalises mine, is to clean the filter bag. Take it off, turn it inside out, and shake it out. Do it out doors and on a windy day. Stand up wind. I was stunned at the dust that came out and the improvement in the suction. The bag clogs over time and you don't miss the suction until you realize what cleaning does for it.

Not sure I want that internal screen. I would think the shavings from my lathe would stop it up almost instantly.

Re: Dust collector issue uncovered

#3

I removed mine

Mike Schwing from Md.

>Turning shavings clogged it constantly. I doubt planer or jointer chips would ever cause it to clog, but shavings, all the time. Every now and then I too suck up something big enough to go BANG! when it hits the blade, but in nearly 10 years it hasn't caused any visible issues.

Re: Dust collector issue uncovered

#4

Re: I removed mine

Alan in Little Washington (NC)

>Remember, most DC bags are "designed" to cake up. That is where they do their best filtering of the fine stuff. After cleaning typical filters dump a lot of fine (bad!) dust back into your shop.

Re: Dust collector issue uncovered

#5

Big Bang Theory

Tony - Memphis

>I heard a big bang the other day....it was my DC remote. Ouch. Thank goodness for Ebay - $2 replacement instead of $20 (X10 remote). I never ever ever use a "naked" hose. I even made a collector using an HVAC outlet and put hardware cloth over the opening. I just happened to have the hose on the bench for a quickie routing job and didn't even see the remote. The funny thing is that the DC was off and winding down when it grabbed the remote. It was like slow motion - I could hear it going through the tube and knew right where it was as it traveled. Don't think it hurt the impeller at all, but the remote was toast.

Tony

Re: Dust collector issue uncovered

#6

Re: Big Bang - Not Theory

Mark Mandell - Gone Round In Jersey

>After I finished upgrading my system to 6" with a BA (6'x 1 mic)bag for the garage-sited DC, it grabbed one of my screwdrivers (although I didn't find out 'til later). What I did notice was that the DC was getting a lot louder. Figured it was just all that extra air moving up the pipe.

It finally got so loud I was getting complaints from YKW, so I opened the impeller and took the blower off the wall mount, figuring a motor bearing had finally died (10 years). Found 4 big chuncks in four blades that were also bent and the aforementioned screwdriver sticking out of the 5" HD flex pipe between the blower and the bag ring. Out to the welding shop to have the impeller blades straightened, filled and rebalanced. Why? Because nobody will sell you a new impeller for anything other than their own machine, so it was either fix the Reliant or buy a whole new system.

$40 repair, and it runs better than ever now, but I'm a whole lot more careful about what goes up those pipes. Since I also turn, the bulk of my lathe shavings get shoveled rather than sucked.

Play "Ring the DC" and it's liable to result in loss of efficiency and noise from out-or-true impeller vanes. Play Big Bang, and it's liable to cost you a new DC.

mm

Re: Dust collector issue uncovered

#7

Re: Big Bang Theory

john lucas

>Tony I did the same thing. Fortunately I was using flexible hose so I jumped forward and stomped on it. Then I had to figure out how to get to the wall to unplug it while still standing on the hose. :)

Re: Dust collector issue uncovered

#8

Re: Big Bang Theory

Barry Irby

>About the "cake" on the bag....I know that's part of the filtering effect. It reduces the size of the holes and "improves" the quality of the filter. I'm sure it does, but I wonder if the rating of the CFM is established with a caked or uncaked bag. I'm guessing its a new uncaked bag and no hose or ducts on it at all.

If you suck up something you shouldn't and you are quick enough, you might save it from the howling vortex of death by stopping up the inlet hose quickly. I shoved my arm into mine once. When the air flow stopped the object stops also. I have also slapped mine flat against the floor to restrict the airflow more than once.

Re: Dust collector issue uncovered

#9

Classic funny!!!!!!

Mark Goodall - ATL - tooljunkie

>

Re: Dust collector issue uncovered

#10

Re: Big Bang Theory

Dick Coers

>My scare came from sucking up an empty coke can. I waited for the crash as I jumped for the remote fob, nothing. Pulled the hose and the bottom of the can was sitting on the center of the fan hub. It stayed centered up, just rattled there till it stopped. Nice suprise!

Re: Dust collector issue uncovered

#11

Re: Dust collector issue uncovered

Bob Entwisle in NJ

>I was glad for that screen on my Griz 2HP when I watched the DC remote get sucked into the hose, I ran for the off switch expecting to hear a crunch at any moment, after the DC wound down I pulled the hose off and there was the remote clinging for dear life to the screen! I've not noticed any problems with planer or jointer chips, haven't done enough turning yet to see if the shavings will pose a problem.

Re: Dust collector issue uncovered

#12

Major DC improvement Recommendation

Barry Irby

>Two or three of you guys have fessed up to sucking up remote switch for you DC's. Several were destroyed. You need to improve the Remote by adding some sort of big handle on it that will not go through the pipe. Check out a woman's purse where she has that big wad of stuff on her keys. That would work. Or just a couple of sticks set in a cross. Paint them bright blue or orange so you can find it easier.

I don't need this, because I use the automatic gates.

Has anyone seen my dust mask and safety glasses?

Re: Dust collector issue uncovered

#13

Re: Major DC improvement Recommendation

Mark Mandell - Gone Round In Jersey

>They're on your head . . .

Re: Dust collector issue uncovered

#14

LOL!!!! :)

Pete Stahl

>

Re: Dust collector issue uncovered

#15

Thank Goodness!!!, I thougtht....

Barry Irby

>my DC had eaten them.

Re: Dust collector issue uncovered

#16

My remote is hooked to my apron strap.

Art Silva

>