Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Sorry, crown molding ( again ? ) . . .

Posts

Sorry, crown molding ( again ? ) . . .

#1

Sorry, crown molding ( again ? ) . . .

steve mackay

>Gonna try it. Trying to do my homework before bothering folks here but . . . I find a backer or nailing strip behind the molding on some pages and none on others. FOR A ROOKIE . . . do I want a backer ? In the end, will this save a bunch of frustration trying to find something to nail to in the ceiling ?

Re: Sorry, crown molding ( again ? ) . . .

#2

Re: Sorry, crown molding ( again ? ) . . .

Ron Hildreth

>Steve,

You shouldn't need any type of a backer board. Your framing top plate should be sufficient, just make sure your finishing nails are long enough to penetrate through the dry wall or plaster and into the framing.

Ron in Iowa

Re: Sorry, crown molding ( again ? ) . . .

#3

Re: Sorry, crown molding ( again ? ) . . .

Barry Irby

>If your framing is typical of the framing here, you should have two 2 X 4's top plates on the wall and a drywall return on top the wall that projects over the ceiling and inch or more. You have to deduct the thickness of the drywall from this, but if your crown is less than about 4 inches wide, you should be able to nail any where you want, if the nails are long enough. (Have you considered trim screws?)

If your framing is not as I described or you are using multi-part or larger molding, you need to consider what you are going to nail to.

Re: Sorry, crown molding ( again ? ) . . .

#4

Re: Sorry, crown molding ( again ? ) . . .

Mark in Whitby

>Obviously you will be able to find ceiling joists running perpendicular to the CM to nail into on two walls, and the wall studs to nail into for ALL walls.

For the two walls where the ceiling joists are running parallel to the CM and likely not where you need to nail the crown up into, you can still nail into the ceiling (reccommend using a nail gun with 2" brads that will bend and curl a bit when entering the moulding and drywall ceiling drawing the moulding somewhat tighter and giving you some grip.

Make sure on these parallel joist walls you catch every single wall stud you can, and the corners, and that the moulding is properly postioned and held tight to the ceiling when nailing the into the wall studs. If it is properly positoned to begin with the nailing into the wall studs and ceiling will help hold it tight.

I have also used a light bead of caulking along the top of the CM to stick it a bit to the ceiling before nailing for added adhesion.

Don't use to much or it can disorient the correct position of the moulding.

Over the last 4-5 years I have done 6 rooms of my house in varying styles of 4-6" pre-primed MDF Crown this way, and finished it off by caulking the top and bottom of the moulding and all corners before painting, to fill any gaps caused by ceiling irregularity or slightly crooked walls.

I have tight inside joints (coped) and tight stable outside corners with no signs of movement or gapping.

As far as I know, this way may be the totally wrong way to do it ....but the results speak for themselves and have held up 100%.

Main thing is I have never seen any gap issues at all espesscially from not being able to nail directly into a ceiling joist on those two walls.

Good luck the look is really worth the effort it when it's all done.

Mark

Re: Sorry, crown molding ( again ? ) . . .

#5

Turning the two troublesome walls into easier ones

Mark Goodall - ATL - tooljunkie

>So far, I've used the 2-piece crown approach: a piece of floor molding turned upside down on the wall, and then the crown molding on that and touching the ceiling directly.

The two walls that have ceiling joists ewvery 16" or 24" are easy, but those two darn troublesome walls that run parallel to the joists are maddening.

So far, I've been lucky. I simply went into the attic, pushed away the insulation and glued down a 2"x4" ontop of the drywall about 3" from the edge of the room. Then those two troublesome walls became the easier walls, because instead of trying to hit a celing joist every 16" or 24" inches, I had the whole length of the 2x4 in the attic to hit.

In one of the rooms that I have yet to do, I'm not able to get into the ceiling to laydown an extra 2x4. In that case, I'm planning one using another piece of floor molding (like the upside down one on the wall). I'll fasten it to the ceiling with screws and anchors and a bit of glue, and then have something to shoot the nails into on the ceiling.

I don't think this has been mentioned before, but this is a perfect reason that I choose the more expensive primed pine moldings, instead of the cheaper primed MDF moldings. The MDF moldings are much heavier. And besides MDF is horrible to try to cope cut. Pine is much easier. In one small room where I could neither get a 2x4 up in the ceiling, nor put a extra piece of floor molding on the ceiling, I used that extruded foam crown molding. It's horrible stuff to use, doesn't cut well, just breaks when you try cope cuts, and dents too easily, but it's as light as balsa wood and hopefully won't pull down as much as wood.

Happy Woodworking!

Re: Sorry, crown molding ( again ? ) . . .

#6

Re: Sorry, crown molding ( again ? ) . . .

George Koch

>Steve, If you are planning on using a nail gun, you should find each stud and ceiling joist center by probing with a nail or awl and extending that line with pencil out beyond where the crown will lie to insure you are firing into backers. If hand nailing into double top plate, I've found it best to use 16d finish nails for 4" crown and 12d for 3". If your crown is 5" or larger, try to get nailing both in wall and ceiling. George

Re: Sorry, crown molding ( again ? ) . . .

#7

Thanks folks ! Confidence is high !

steve mackay

>