Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Kitchen oven for kiln??

Posts

Kitchen oven for kiln??

#1

Kitchen oven for kiln??

Phil Joines Krum, Tx

>I need to turn a commemorative platter by Feb. 3 and the only suitable wood I have is a 6/4 x 18� green Mesquite disk. Has anyone tried to dry something like this in a kitchen oven? The piece is pretty solid for Mesquite. I�ve done smaller pieces (bowls) in the microwave but this one is too wide to fit.

I�m thinking of using 150 deg.F for about 4 hours, cooling and repeating until it looses most of it�s weight. Don�t have a moisture meter.

Anybody ever tried something like this?

Re: Kitchen oven for kiln??

#2

JL

Re: Kitchen oven for kiln??

JL

>I've dried rough turned legs and rough shaved spindles in a hot box before at ~130 degrees F for 2-3 days. The legs were ~2" in the largest diameter and the spindles were ~3/4" in largest diameter. They got reasonably dry after 3 days.

The pieces did go slightly out of round - so that's something you have to consider. Slower might be better for your slab - and I don't think you should tie up the oven for that many days :).

How about building a small box out of plywood with the inner surface being covered with insulating board? You can use a shielded light bulb (or two) as your heat source (or a small heater).

Re: Kitchen oven for kiln??

#3

Agree

Mark Mandell - Gone Round In Jersey

>with the Hot Box idea.

Put your light(s) on a cheapo timer and have them cycle on/off every 4 hours. Make sure to put convecvtion vents near the top and bottom of your box, and check your temperature to adjust the wattage you'll need (or consider a dimmer switch). Remember, the kids EZ Bake ovens use a light bulb for a heat source and there's no such thing as "low temperature flour". You don't want to start a fire with this thing.

mm

Re: Kitchen oven for kiln??

#4

Re: Kitchen oven for kiln??

JohnKJordan in East TN

>Phil,

I haven't tried a kitchen oven, but I have used a microwave oven to dry 4/4 pieces. Perhaps it would work on thicker wood.

Following advice I read elsewhere, I used the "slow and easy" approach. I heated the pieces until they began to feel warm, let them cool, then repeated. Just before each reheating, I weighed each piece and wrote the weight on the wood. When the weight quit changing significantly, I was done. After several hours the wood was dry and ready to turn.

For another perspective on microwave drying, here's a note I saved from Russ Fairfield:

------------------------------------------------------------------

Microwaves and Pen Blanks

By Russ Fairfield (11-05-2000)

I use a lot of wood pieces that are either pen blank size or 2-1/2" square by 1" thickness. All need to be dry for turning. Because they are usually burl, wild grain, knots, etc. there is a lot of cracking during the drying and I was losing as much as 90% of the green Madrone and Myrtle burl and spalted Holly.

I gave up on boiling the wood. Beside the mess and time to boil the wood (1-hour in an open pot and �-hour in a pressure cooker), all of the color was leaching out of the wood, and the drying losses were only slightly less than that of un-boiled wood.

I figured that I would need more heat and less water, so I tried the microwave oven. Running Madrone and Myrtle burl on high for a sufficient time to get the internal water boiling out of the wood, then reducing the power level to hold that heat level until the water stops bubbling out of the wood (about 5 minutes), then letting it cool down in the oven, and then putting it into a vented box with a light bulb to maintain an 85-90F temperature until dry. My losses dropped to about 10%, with no loss in color.

This is totally contrary to the slow and easy approach to Micriwave drying that we would use on a bowl. The wood gets hot quickly and the water starts to boil out of the wood before there is any evaporation from the surface. 6 blanks arranged in a radial pattern on the rotating plate is the perfect load for the Microwave oven.

Added Note:

(My vented box is the old dishwasher described in Russ�s Corner here on Wood Central.)

After the microwave zap, the wood has done most all of its deformation, so from there on all it will do is to dry. Being burl, there are still some small shrinkage voids, but nothing that can�t be repaired.

This success prompted me to do some trials with pieces up to 3x3x6 (weed pot stock), and it didn�t work as well. The problem with the larger pieces is that the home Microwave oven doesn�t have sufficient power to get the water on the inside to boiling temperature without the wood starting to dry on the outside, and this is the perfect condition for cracking.

------------------------------------------------------------------

JKJ

Re: Kitchen oven for kiln??

#5

Lee Grindinger

H2O migration

Lee Grindinger

>The speed at which water migrates through the wood tissue is the speed at which water can be removed from the surface. If you exceed this speed surface checking occurs because the surface shrinks around the still fat and wet core. Stresses develop as these tissues are stretched and compressed. Mesquite might be one of the tougher woods to dry quickly and putting it in a warm dry oven will be very risky because ovens have no control over humidity which needs to remain high in early stages of drying.

For my money it's not going to work but if you do it anyway let us know how it turns out.

Got a vacuum chamber? That's the quickest way because the boiling point of water is so low in a near vacuum. Steam moves through wood tissue much quicker than liquid.

Lee

Re: Kitchen oven for kiln??

#6

Re: H2O migration

Mark Williamson

>I have heard many mentions of a vacum chamber? How do I build one of these vacum chambers? Or is this somehting you just have to purchase?

Mark

Re: Kitchen oven for kiln??

#7

Lee Grindinger

DIY vacuum

Lee Grindinger

>I don't think it's practical to put together a vacuum chamber for just the odd piece of wood to dry. You'd need a vacuum pump, an airtight chamber and warming platens of some sort. If you were already set up with a vacuum press for veneering a bag can be used but it means a lot of tending.

Enter "vacuum kiln" with the quotes into Google for more information. Vacuum kilns work great on things like baseball bat blanks and other premanufacture blanks with consistent sizes, it does not work well on random sizes because heating platens are necessary.

Lee

Re: Kitchen oven for kiln??

#8

Lee Grindinger

Mark, also

Lee Grindinger

>There is another thread about lumber drying right now in which I posted a link to Dry Kiln Operator's Manual. It's the entire book in PDF format. Look at the section entitled Kiln Types and Features for vacuum drying information. It will give you a good overview of the principles.

Lee

Re: Kitchen oven for kiln??

#9

Ask a turner

Bill Tindall, E.TN

>the turners handle this situation all the time. They have tricks that work, for example ethanol soaking, microwave, etc.

If you put that piece into the oven at the lowest controllable setting the oven will achieve, it will be 0% moisture in 4 hours. If the oven is electric the radiant coil heat will heat the surface to well over the set temperature.

I use the oven to measure wood moisture content. 4/4 lumber will go to zero at 220F in about an hour. Of course I don't care that the ends will open up cracks 1/16" as the piece dries because it is only a test piece.

Re: Kitchen oven for kiln??

#10

Lee Grindinger

As per Bill's suggestion..., *LINK*

Lee Grindinger

>Dave Smith did a presentation at MontanaFest a few years back, here is the technique he uses with great success. It sounds like it's precisely what you need,


Alcohol drying

Re: Kitchen oven for kiln??

#11

Cool Thanks for the info!

Mark Williamson

>