Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Waterborne spray finishes

Posts

Waterborne spray finishes

#1

Waterborne spray finishes

Clint Searl, at the base of Haycock Mtn

>I am considering diving into a waterborne spray finish for furniture and cabinet work. The Oxford lacquer and poly products look like reasonable choices. All thoughts and opinions welcome.TIA

Clint

Re: Waterborne spray finishes

#2

Re: Waterborne spray finishes

Mark Mandell - Gone Round In Jersey

>Hey Clint,

The Target products are quite good, especially the 9000 poly. I haven't used the Hibrivar yet, but I've heard good things about it. I have used both PSL (gone) and USL lacquer, and, frankly, I've had too many issues with it to continue. The product seems to have a limited shelf life so that when I used it over a fresh tie coat of dewaxed shellac (silicone free) I got big-time fisheyes; it was not pretty.

Instead I've worked Fuhr 350 (nice) and (even better) General's Enduro Clear gloss with and without added crosslinker. This is a super product that goes down like glass off-the-gun on vertical surfaces. When I rubbed it out on a cherry table top with Meguire's No. 3, my wife got upset that I would put a piece with wet finish in the living room! |;-}}}

Hope this helps.

Re: Waterborne spray finishes

#3

Ellis Walentine

Re: Waterborne spray finishes

Ellis Walentine

>I am not an expert on waterborne finishes, but I've used Velvit Aqua Shield on turnings and I like it a lot. It is thin enough to spray, dries quickly and leaves a soft gloss sheen.

I have some you can try if you want. Lemme know.

Ellis


img

Re: Waterborne spray finishes

#4

Re: Waterborne spray finishes

Chuck Kettler Greenwood IN

>I converted to water borne so that I could turn around cabinets quicker. Target products are very good. I don't have issues using over shellac as I use a thinned quantity of the topcoat as the sanding sealer. I use a DeVillbis suction gun. Should be using a HVLP, but the new gun would buy me enough over spray the rest of my life that I see no reason to convert.

Re: Waterborne spray finishes

#5

Re: Waterborne spray finishes

NickB

>Mark,

Are you using the General Enduro acrylic or poly? I've been using Fuhr 255, which I can spray pretty well and does well brushed and wiped, but Jeff Jewitt is no longer distributing...

Thanks,

Nick

Re: Waterborne spray finishes

#6

Re: Enduro

Mark Mandell - Gone Round In Jersey

>Hi Nick,

I'm using the Enduro Clear Poly gloss. Straight from the can for vertical elements and with cross-linker added for table tops.

mm

PS: You can still get Fuhr products. Just google the name; I think the company sells direct. Don't know why Jeff dropped the line (or they dropped him), but not really my concern (or business).

Re: Waterborne spray finishes

#7

Thanks for the responses and offer

Clint Searl, at the base of Haycock Mtn

>After speaking with Jeff at Homestead, I'm going to try Enduro Acrylic. It won't get here for a week or so, but when it does, I'll share my experience.

Clint

Re: Waterborne spray finishes

#8

Just what I found..

Joe Burke

>Clint

I tried the Fuhr products, and while they showed promise, I couldn't ever resolve all the issues I encountered. The consensus among all the experts was that environmental issues are almost always the culprit. In short, the weather.

Here in NC the weather swings so wildly that I couldn't ever get a bead a constant set up. Every time I shot was an adventure.

I really wanted to use the tinted fuhr finishes for my painted work, and did with some success. I've used the clear finishes on drawer boxes and the like, but never liked the look on anything else.

The bottom line was that I needed more consistancy than the water based stuff would give me. I had to go back to the dark side. It doesn't hurt that I have a major distributor for a good solvent based product within 5 miles of the shop either.

I wanted the water based stuff to work in the worst way, but it just wouldn't for me. More power to those that can.

Re: Waterborne spray finishes

#9

Re: Waterborne spray finishes

Randy Stukenberg

>ML Campbell has a new product out called "Agualente" in both pre-cat and post-catalyzed laquer. I used it for the first time last week and really liked it. I'm not a great finisher, but got great results with my new Fuji Q4 turbine hvlp sprayer. I have talked to several shops around the area that have used it and gave it great reviews (the laquer, that is). It is available in gloss, satin (really more like semi-gloss) and dull sheens. Supposed to be super tough, especially the post-cat version.

-Randy

Re: Waterborne spray finishes

#10

Poor Results w/ Enduro Poly in Kitchen Application

Philip

>I used the Enduro Poly a few years ago on a set of kitchen cabinets. It was fairly easy to use and went on well. However, it did not hold up well to moisture in the kitchen: I would not use this product where it will come in contact with moisture (the type of incidental contact you would normally expect in a kitchen).