Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

quarter oak warping- help!

Posts

quarter oak warping- help!

#1

quarter oak warping- help!

Alex

>I just finish cut many small quarter sawn oak strips- 1/2"X 1/2" X 27" lengths for a plant stand project- but after a week they're warping like crazy! The wood sat here (winter, dry midwest, zero humidity) for two months, but it's been "released" or something- any way to straighten them or prevent it from happening again? Very frustrating- thanks for any responses to this admitted newbie...

Re: quarter oak warping- help!

#2

Re: quarter oak warping- help!

Rob Stokes in North Vancouver

>Were the pieces laid flat on another surface for a few days? Did they all cup the same way (up or down)?

Reaction wood usually shows itself the instant if comes off a saw blade so if it was internal stresses in the wood causing the problem you'd have been cursing the wood long before now.

Which leads me to thing that it's unequal moisture levels in the wood when comparing the "up" side of the stick (the horizontal face open to the air) with the "down" side (the face that was on the table/bench).

The "up" side either shed or gained moisture freely as it was open to the atmosphere. The "down" side would have been inhibited from doing the same thing as it was in contact with a surface. As the moisture in the "up face" changed, that face expanded (if the moisture level in the wood increased) or contracted (if the moisture level in the wood decreased) accordingly. Thus the warping you notice.

It's (typically) easier to add moisture than it is to remove it and there's several ways of doing this. If it was spring, I'd suggest you put the pieces on the lawn with the "dry" side face down. Instead, you may want to simply flip the pieces over and see what happens after a few days, or place them face down on the bathroom counter next time you have a shower - and leave them in there a while, or you can even try moistening the wood with a damp sponge. If the pieces are severely cupped and won't actually contact the surface you lay them on, try covering the "wet" surface with masking tape to prevent over saturating it as you attempt the black magic tricks.

Whatever your chosen method, you need to equalize the moisture content in each of the four sides. And while the methods I describe are usually successful when dealing with a plank, dealing with a stick is a bit harder as "straight" is typically a more accurate measure with a stick. But it's worth a try.

Next time you make sticks, or want to leave wood for a while after milling it, sticker it properly and you shouldn't have this problem repeat itself.

Good luck!

Rob

Re: quarter oak warping- help!

#3

Re: quarter oak warping- help!

Malcolm Timbers in British Columbia

>Is there any sapwood on one side? If so it will bow toward that side. Otherwise the only way to straighten reaction wood is to rip it in half turn one side around and glue it back together.

Re: quarter oak warping- help!

#4

Re: quarter oak warping- help!

Bill Tindall, E.TN

>can't help with straightening, but wife would like some plant stands. would appreciate a picture when you are finished.

Re: quarter oak warping- help!

#5

Re: quarter oak warping- help!

Dick Coers------WebKitFormBoundaryqFOmq51H3saAc+aC

>Quarter sawn white oak is very difficult to dry in the kiln. What size stock did you take the 1/2 x 1/2 strips from? If it was thick stock it may have not been dried through and through. You got into some wetter wood in the center of the stock and exposed it to the dry winter air. That will warp it every time. I had the same problem with some 1/4"x 3" x 48" slats I resawed for a room screen. I took them back to the supplier and veneered some 1/4" mdf for the slats. With the tight spacing, and dark stain, I left the edges of mdf raw and they don't show at all. Good luck.

Re: quarter oak warping- help!

#6

Re: quarter oak warping- help!

Warren in Lancaster, PA

>Sticks of wood this thin are vulnerable to both warping as they are cut from the board and also warping as a result of humidity changes. If I were making these pieces, I would saw them somewhat oversize either 5/8 square or 3/4 square. Then I would hand plane a flat edge, plane an adjacent edge flat and perpendicular. Then mark and plane the other edges parallel. And try and use them right away rather than letting them sit around.

Incidentally, it seems somewhat odd to refer to square stock as quartersawn. Cutting strips like this from a plainsawn board will yield the same grain configuration.

Re: quarter oak warping- help!

#7

Re: quarter oak warping- help!

Larry Barrett

>Alex - in making chairs it is common to bend wood (chair posts, slats, etc) by heating it. I usually use riven wood that is near perfect to start with. But having seen how easy it is to put a bend into wood, I recently have been using heat to take bend and even twist out of wood. Heat it up in a steam box or in a tub of hot water. Get it as hot as you can. Pick it up with insulated gloves, put one end in a vise, and pull/twist in opposite direction. As you apply pressure the wood will resist at first, but within seconds you will feel the wood relax. If the bend/twist is more-or-less uniform, you only need to loosely place one end in the vise, and move it up or down as you pull/twist. Once it cools the game is over, so you only get a minute or so to do this. Sawn wood may not behave as nicely as riven, but it might be worth a try.

Larry - in Maryland