Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Water Uber Oilus?

Posts

Water Uber Oilus?

#1

Water Uber Oilus?

Mark Mandell - Gone Round In Jersey

>Am in the final stages of an ash table for the game room.

I wasn't watching my stock and I wound up with sticker-stained boards in the top, so I'll have to A/B bleach out the top to white (oxalic wasn't enough) and then recolor. Stain will be a medium brown water dye followed with walnut-flavored Watco oil.

I'm planning to use cross-linked Enduro waterborne as the finish as it will see some traffic.

Question is: If I let the Watco set and cure for a week at 65* before applying the waterborne, do I need a shellac tie coat or will the waterborne adhere properly without it?

[No, I will not be using oil poly.]

TIA

mm

Re: Water Uber Oilus?

#2

Thou Shall

Mark Mandell - Gone Round In Jersey

>"Not be putink za vater on ze erl mitout za shellacinzee."

Zo shpake Homestead General Finishing Forum.

I figured as much, but just felt like checking with the host who know more than I.

Thought I'd pass this along to those on WC who were wondering about the answer.

mm

Re: Water Uber Oilus?

#3

Thanks Mark and a Question?

Barry Irby

>The wood bleach.....is it powerful to take a pet stain out of oak flooring? This comes up here once and a while and often in my work as a home inspector. What I was wondering was could you sand the entire floor, bleach all of it and then stain it back to some acceptable color?

Never knew anyone to have luck with just bleaching the spot. Turns white and never matches the rest of the floor. But, could you do the whole thing?

Re: Water Uber Oilus?

#4

Re: Bleaching Wood Floors

Mark Mandell - Gone Round In Jersey

>Hi Barry,

You could, of course, sand the floor to bare and then bleach it. However, the A/B wood bleach (2 parts) is pretty nasty stuff and will require neutralization (white vinegar does fine). Then, too, the bleached layer of wood fibers is rather thin; easy to sand through. The stuff ain't cheap either. Before you were done you might find it cheaper to replace the floor, or at least the discolored boards.

There are a number of products on the market to neutralize pet stains, and while I have limited experience with wood floors, I think I would try to spot sand and then bring the spot back to match the surrounding area by tinting in the coating. Are you sure the stain is in the wood rather than in the coating?

Again, I think I'd try to spot sand and refinish, but there are several flooring guys here ( Jason? Andy? ) who may have some better tricks.

mm

Re: Water Uber Oilus?

#5

More Info *LINK*

Mark Mandell - Gone Round In Jersey

>At the link.


Bleaching

Re: Water Uber Oilus?

#6

Re: Thou Shall

Joe Dusel (Vista, CA)

>That's funny, I have used Watco under waterbased finishes on a number of jobs with no problems. I did let the oil-varnish cure for 3 or 4 days.

Joe

Re: Water Uber Oilus?

#7

Re: Thou May

Mark Mandell - Gone Round In Jersey

>Hi Joe,

Interesting. Which waterbornes and what were the applications?

Re: Water Uber Oilus?

#8

Re: Thou May

Joe Dusel (Vista, CA)

>I've done ApolloCoat and Target USL over the Watco. I did have an amusing experience here with a friend who used an oil based stain, shellac and then Target CV. Unfortunately my friend sprayed Bull's Eye Shellac, not SealCoat. The shellac has wax in it, so the CV just pealed off in sheets. Pretty funny as a bystander. Lots of French was spoken by my friend.

If you are using Target products you might want to ask them about it as well. I believe a lot of their water-borne products actually contain oil.

Joe

Re: Water Uber Oilus?

#9

Jason Roehl in Lafayette, IN

Not uncommon...

Jason Roehl in Lafayette, IN

>...for waterborne products to contain other solvents, including "oil". That's why they're called "waterborne", not "waterbased". To me (and I think the coatings industry in general as well), "waterbased" means that the solids are water-soluble. Pretty much only kids' finger-paints fall in this category. Re-wet them and they run. "Waterborne" finishes use water as a vehicle (it's cheap), but once it evaporates (quickly), other curing processes take over so that (non-submersive) water contact does not affect the cured finish readily. Other solvents are used that act as intermediates between the solids and polymers and the water. One of my favorite waterborne finish paints even has mineral spirits listed in the ingredients.

Jason (pro painter)

Re: Water Uber Oilus?

#10

Wax Off

Mark Mandell - Gone Round In Jersey

>Kind of a tough way to learn.

Since you mention Target and SealCoat in the same sentence, I'll pass along a caution from Jeff Weiss (Target owner). Do not use SealCoat that is more than 6 months old if you want to avoid the risk of cold checking in a waterborne top coat. This happened to me with dewaxed garnet that was key in my finishing program for cherry. [Watco + shellac + PSL / USL] When I called Target to complain, the first thing he asked was whether I had used SealCoat as the tie because they were having a lot of trouble with cold checking. I now mix my shellac in small batches, use less, and pitch any unused portions after 3 months.

As I use shellac as both a tie and a wash-tint, I'll still continue with it.