Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Freud SP500 dado blade

Posts

Freud SP500 dado blade

#1

Freud SP500 dado blade

Lee Ohmart

>I bought a Freud SP500 Super Dado blade set and am disappointed in the performance. When I tried it out on my Craftsman tablesaw, the sides were cut beautifully but the bottoms were uneven. Interestingly, no matter how I stacked the blades, the cut was uneven in the sam spots. Anybody else have this problem? Solutions?

Re: Freud SP500 dado blade

#2

The Answer

Marvin Horn

>Older Craftsman's have an undersized shaft (threaded portion) with a raised boss next to the hub for the blade to rest on. This centers a single blade but a dado set will be randomly offset except for the inside blade next to the blade.

My solution was to place a thin brass shim on top of shaft while I was installing the dado cutters. The shim was (if I remember right) slightly less than half the "undersize" of the threaded shaft. You have to keep the shim on top of the shaft so that it raises each cutter to the center point. There was a real learning curve in doing this essentially blind though the insert opening, my hands are definitely not dainty, but buy the time I sold the saw it was second nature. Hope this helps. Others may have another solution.

Re: Freud SP500 dado blade

#3

Re: Freud SP500 dado blade

Ron Hildreth

>Lee,

I have the same dado set, and although not perfect, not real bad either. Other than using too many shims between the chipper blades, I wouldn't think there is a reason for the bottom to be that rough, unless mis-cut from the factory. Maybe a stupid question on my part, but are all the teeth on the blades pointed toward the front of the saw? I was in a hurry once and stacked several of mine in backwards. Just as I was about to complain here on the board, I decided to recheck everything, and caught what I had done. I felt really proud of myself that I hadn't made a fool of myself (although now everyone knows!)here on the board.

Ron in Iowa

Re: Freud SP500 dado blade

#4

Not uncommon in a dado set.

Forrest Addy

>Ths problem you describe is not uncommon in a dado set. Fortunately, a good finish on dados and grooves is not a real necessity. In most woodworking, a shelf or something is glued in it concealing the irregularity forever. However knowledge of a less than perfect finishes and joint geometry anywhere detracts from the pleasures of fine woodwoking. The problem derives from the relieved diameter of the threaded arbor and the tendancy of the thinner chippers to drop slightly between thread crests if there is room for them. A saw arbor is a weak design; there are many disadvantages and few benefits to an Acme or square threaded arbor.

I always thought woodworking machinery should borrow from metalworking and use a self-releasing taper to locate spindle tooling and adaptors to interface betweeen cutting tools and the spindle (arbor). The adaptor would fit a keyed 3 1/2" per ft taper on the arbor and be retained with an allen screw. Thus all woodworking saws and dado heads, molding heads etc would have a precise 1 1/4" bor that fits a unuversal hub on the adaptor.

This is not only more precise and rigid but tooling changes are quicker. A half dozen hubs and you could have the all-purpose combo saw, a thin kerf, the junk nail cutter blade, the dado head, a molder head, etc all set up for quick and ready swap. And you can assemble the dado head out where you can get at it instead of in the bowels of the saw table.

I've sketched it out a time or two ahd the whole system would impose no bulk that would inhibit the range of motion or adjustment of the presently used table saw design. In fact the hubs would be almost identical to those used on tool and cutter grinders.

But it's expensive and saw arbor tooling to be used with it would have to be bored to suit the hubs. Don't look for it in the near future.

Re: Freud SP500 dado blade

#5

Re: Freud SP500 dado blade

Lee Ohmart

>I did check the direction of the blades.........several times. Everything was aligned as instructed on the DVD. I also reorganized the chipper teeth to see if I could find one high blade. No good. One other thing I did was send a message to Freud to see if they had seen this problem before. I'm thinking that it's something germain to the Craftsman saw. Maybe I'll have to upgrade to a cabinet saw because of this blade. Yeah, that's the ticket. The wife will surely buy THAT arguement.

Re: Freud SP500 dado blade

#6

Re: The Answer

Lee Ohmart

>I was afraid I'd have to shim the shaft. Where is a good place to get brass in various thicknesses?

Re: Freud SP500 dado blade

#7

From the dark recesses of my mind…

Rod Peterson -- Ormond Beach

>…I seem to recall a discussion on the Ridgid Woodworking Forum some time back regarding the arbor on not only the then current Ridgid table saws, but their antecedents, the much maligned Craftsman table saws from time immemorial. Dave Arbuckle has been a semi regular there in the past and might be able to shed more light on it. In any event, at one time Emerson was offering replacement arbors (perhaps gratis, although I suspect that's no longer the case) that didn't have the undersized section described by Marvin.

I tried to do a search to see if I could find some of the original discussion, but my search parameters weren't good enough considering the time I was willing to spend. However, I did find some threads with suggestions including the shim Marvin suggested and one that used a filler of some sort (Weldbond in one case). The most significant conclusion I reached was that any of the workarounds was more than sufficient to resolve the problem and that replacing the arbor wasn't worth the effort.

Now you know what to do.

Rod

Re: Freud SP500 dado blade

#8

A more complete answer… ___(coupla *LINKs*)

Rod Peterson -- Ormond Beach

>Not satisfied with my initial effort, I refined the search and although I didn't find the thread in which I was specifically interested (for the history), I did find this article which is a step by step repair procedure involving JB Weld, and written by John White, no lightweight when it comes to machine tool maintenance (the manager of Fine Woodworking's woodshop for almost a decade and the author of Care and Repair of Shop Machines).

If I still had my Craftsman saw, this is exactly what I'd do with it.

Rod

Re: Freud SP500 dado blade

#9

Re: The Answer

Marvin Horn

>Any FULL SERVICE auto parts (non-chain) should have shim stock. Same comment applies to hardware stores if such an animal should exist in your area.

Re: Freud SP500 dado blade

#10

Also hobby stores…

Rod Peterson -- Ormond Beach

>There is frequently a countertop bin with brass stock of all sorts—rod, tubing, sheet, etc. (also aluminum, in some cases).

Rod

Re: Freud SP500 dado blade

#11

Re: Another option

Howard Acheson

>As said already it's a long time problem with Craftsman and early Ridgid contractor saws. There are two issues. One is that there is a groove between the threaded portion of the arbor and the flat area. Whatever chipper that sits in this area will cut in a non-concentric path cutting deeper. The second issue is that the threaded portion of the arbor is slightly smaller in diameter again allowing the chippers and blades resting on this area to cut in non-concentric paths. It's not quite as much or an irregular path as the other area but still will cause less than perfect dado bottoms.

One thing many have done over the years is to clean the grooved area thoroughly with acetone or lacquer thinner. Then fill the groove with a metal epoxy like JB Weld. Overfill the slot. Once cured, use a file or sandpaper to smooth the fill. This "fix" will eliminate the problem with the slot. There is no way to fix the smaller diameter threaded portion except to use shim stock. However, perfectly flat dado bottoms are rarely a problem so you might just ignore that problem.