Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Looking for a printed Article FWW?

Posts

Looking for a printed Article FWW?

#1

Alan Young

Looking for a printed Article FWW?

Alan Young

>A few years back (3-5?) Chris Gochnour wrote an article that I thought appeared in Fine WoodWorking on building a French Provincial Case Piece. I am working on a design that has that general flavor. Part of the design is a swooping cove molding that runs around the top.


I think he did this by making strait sections in the table saw -angling the piece across the saw and making several cuts raising the blade each time.

I think he made the corner pieces on the lathe matching the profile than cutting them on the table saw at 90 degrees...



Thing is it seems you can only get 1 corner piece out of the turned sections as the kurf of the saw blade will reduce the radius by 1/8" of an inch on the cuttoff....I want to figure out if I have to make two of the round pieces to yield the two corner sections. I'd like to re-read the article. I am sure I have the article somewhere in my stash- thing is the stash is spread out over a couple of stacks and locations and if I at least knew what issue to look for that would be helpful....

BTW A serch of the FWW site produced 69 articles but I couldn't find the one on this topic. I can see the pictures in my mind....It was really a great article. Details on running bead lines around cabriolet legs, raised panel doors with that jogged curve...I though for sure it was FWW.So if anyone recalls this sort of article in a PRINTED publication and can track it down I'd really appreciate it.

Thanks folks

Alan

Re: Looking for a printed Article FWW?

#2

Re: Looking for a printed Article FWW?

Sonja Lemon Sacramento Ca.

>Alan, How many 90 degree corners do you want? According to my math, you should be able to get 4 out of one turning, or at least 3 with wiggle room. Hmmmm Or don't I understand the problem. Sonja

Re: Looking for a printed Article FWW?

#3

Alan Young

Production order and process

Alan Young

>Hi Sonja,

Yes I can get 4 at 90 degress from one turning but....

I planned on making the straight coved pieces first, producing a turning based on the profile from the long straight coved pieces- ie the sides and the front piece. My plan was to take the resulting profile and run a profile gauge against it-then bandsaw a template from that. That template would be used at the lathe to turn same profile. If I anticipate the order correctly I'd end up with a nifty looking bowl that would be cut in cross sections yielding four equal pieces-except the kurf of the table saw blade would reduce all the profiles by 1/8" of an inch-or what ever the thickness of the saw blade is. My figuring said I could make the first table saw cut so that I get an exact 1/2 for a cutt-off and a 1/2 piece -minus the saw kurf-So that whole half(wow is that bad writing?!) is not usable to the original profile. The remaining section can then be cross cut in half- again one piece at exact radius- the left over being minus the saw kurf.

So that's why it seems I can only get 1 corner piece from a full turning. Now I could make the turning, and make four even cross cut sections but I'd either half to over size the original turning so all the resulting cross cutts come out the same- or make the straight sections afterwards and try to match their profile to the turned sections- That order seems like a lot of guess work.

I don't know if I am being clear or if I'm clear-but clearly missing something :^)

Alan

Re: Looking for a printed Article FWW?

#4

Simple solution…

Rod Peterson -- Ormond Beach

>First of all, if you ever do figure out which issue it's in, I have them all and can help you if need be.

Second, it sounds like you have the process down already. To complete the thought, I'd suggest instead of cutting the segments out of your turning (necessitating the kerf, as you said), glue up the four rough sections with paper separators (precise joinery needed here—no problem for you, I wouldn't think), then split them apart after turning, with no kerf taken at all. That way, you can indeed use all four quarter sections. Norm did this on his Pier Table (I think), Episode 1610.

You might want to ask about the technique on the Turning Board. I'm sure you'll get some advice there.

Rod

Re: Looking for a printed Article FWW?

#5

I know that feeling ...

Joe Burke

>The one where you can see the pictures in the article in your head but can't find it. Frustrating. I can't tell you how many times I've searched through piles of mags one at a time.

I digress ...

June 2000 ... Issue 142 .... page 78 ... Master a Classic Style

I searched his name and it popped up. Pretty sure this is what you're looking for.

Re: Looking for a printed Article FWW?

#6

Alan Young

DOH!

Alan Young

>I went home last night at rifled through every issue-not that I have all that many- But I was a subscriber in 2000 and could not find that issue.

I come into work this morning and 18" away from me under a table is a small stack of various ww mags- including the FFW June 2000.

Thanks Joe for finding the article and Rod for being willing to help out...

Alan