Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Dumb jointer question

Posts

Dumb jointer question

#1

Dumb jointer question

teflon_jones

>Ok I know this is a dumb question, but how do you use the levers on a jointer to adjust it? The ones with wheel adjustments are straighforward and easy, but I've looked at the models with levers and I don't understand how they work. So can somebody please explain the basics behind how you move the beds? And also, would you recommend getting one with wheels, or do levers work fine? I'm going to be getting an 8" long bed model for my home shop.

Re: Dumb jointer question

#2

Re: Dumb jointer question

Barry Irby

>I don't know the answer to your question. My jointer has the hand wheels. I thought the levers just cammed or moved the tables through some trapezoidal type mechanism, but I never looked at one closely.

I find that I want to make two types of adjustments on my jointer. (Actually, about 99% I leave it set at about a 1/32" cut) Sometimes I want to make very fine adjustments and other times very coarse movements. The hand wheels do a fine job on the almost micrometer moves but can be a bit of a struggles for the coarse ones.

Where this is important is when you change the knives. Its important to set all the knives exactly the same height and then set the out feed table exactly the correct height. (To avoid snipe and tapered cuts etc.) The point to all this is that I have read that the lever adjustments are not good at precisely adjusting the tables. They work well for the coarse moves, but not well at all for the really fine ones. This can make changing the knives a nightmare. Or so I have read.

So, Maybe someone will tell us both if this is true. If so, it might be really worthwhile to have the hand wheels.

Re: Dumb jointer question

#3

Re: Dumb jointer question

Pat Evans

>Stop by a store that has a DJ-20 on display and give it a try. I was initially concerned about the lever mechanism, but have found it to be extremely easy to use and plenty accurate.

Re: Dumb jointer question

#4

Re: Dumb jointer question

Hal

>In talking about levers, I assume you are referring to the "parallellogram" type of machine. I bought my Griz 8" (G0490 model I think) a couple of years ago and think the parallelogram is a lot easier to use than one with wheels. The lever on the infeed table simply adjusts the table up and down with relation to the outfeed table. On the Griz, you don't use the outfeed lever unless required for adjustment which I have not had to do. If buying another jointer, I would go with the "lever type" again. Good luck. Hal

Re: Dumb jointer question

#5

Rick L

Re: Levers are better anyway!

Rick L

>Pretty basic. Push the lever down and the table goes down. Don't let levers versus handwheels throw your decision. The better jointer have levers, parallelogram design. It's just as easy to align your outfeed table with the top of the knife with levers as it is with handwheels. There is a stop screw adjustment to regulate the height of the outfeed table. So you can drop the table down and tweak the screw and lever it back up to where the stop is.

I've been repairing jointers and woodwroking machines for 25 years so I've seen pretty much every jointer issue from adjusting to having tables reground.

Re: Dumb jointer question

#6

Re: Dumb jointer question

Tony - Memphis

>Well, the levers are just that, levers! They rotate around a pivot and push/pull the bed up or down the incline. You can see them in the exploded diagram here:

http://grizzly.com/images/manuals/g0452_m.pdf

My jointer has levers. I've never felt like I needed wheels instead. It is very rare that I move the tables anyway. When installing new knives, I've never had any issues with them. Can't argue that wheels might be nicer, but I wouldn't make that the basis of my choice. A more critical issue I have experienced is the pivot point for the fence being sloppy. That means the fence can move a bit when you are pushing against it. Every Griz I looked at was like that and so were the replacement parts they sent me! I fixed it myself with a feeler gauge blade as a shim.

Enjoy your new machine! I would like to upgrade to an 8" myself someday. I have read that the new type heads are really really nice (helical with inserts).

Tony

Re: Dumb jointer question

#7

Re: Dumb jointer question

Chugbug

>Contrary to how puzzling it may appear, the levers work very easily. IMHO, As easy as rotating wheels (on a small table). Obviously, with the wheels, you turn the wheel or "crank it" with the mounted handle. With a LEVER, you lift up to raise the table; and push down on it to lower the table.

How they work (basically)? On the wheel models, the wheel rotates a worm drive to raise and lower the tables. One a lever model, instead of having the worm drive internally they basically dependent on the "greased pig" method of needing to have the "ways" (the channels on either side of the base of the table) greased well for the table to move; and friction to keep them from moving too much.

The main differences (IMHO)? 1. Most folks believe the rotating wheels are more accurate to adjust, which is one reason why you see wheels on more expensive models. The other reason you see them on larger more expensive models I would think is because the wheel (and its internal mechanics) are needed to move a larger table whereas with a smaller / lighter table (6" and 8" jointers) the mfgs can get away with less interal mechanics and the simple "greased pig" slide and lever to move the table.

On some models, as on my 6" Yorkcraft jointer, you may see both. On my YC-6J Yorkcraft jointer, I have a lever on the infeed table, and a wheel on the outfeed table (up until last year Yorkcraft jointers were made/sold by Wilke Machinery in York, PA). I guess the wheel is on the outfeed table because that table needs to have a more fine tuned adjustment in order to opperate properly.

Mine is just coming up on its 4th birthday this week (purchased Jan '04). After using it for the past four years, using the lever has become second nature, and pretty easy to raise and lower the table with it. The table is tight enough, but loose enough that when I pull or push on the handle, the table moves where I need it. Not really any "fiddling around" is needed to get the table set where I need it contrary to what some people suggest). Maybe has to do with having the correct adjustment.

I've been satisfied with my purchase. If you are buying a small jointer (6"), I don't think getting a lever over a wheel is an issue. Not sure if it is a factor on an 8". May be iffy. But on larger models, I'd think wheels would be a must.

Hope this helps...Chugbug

PLEASE NOTE ---IMHO--- These comments are MY-OWN Honest Opinions! Others certainly MAY vary.


img

Re: Dumb jointer question

#8

Rick L

Re: Levers and springs

Rick L

>Lever type jointers all use springs to keep the table easy to move.

The more expensive larger jointers use motors with digital read outs to move the tables. We have a 20" RGA parallelgram, lever jointer that moves very easily. The better machines have parallelogram tables and I've never seen one with handwheels. All the newer and more expensive machines, especially European, are parallelogam machines. The only exceptions are the heavy American one like Northfield, etc

Re: Dumb jointer question

#9

Re: Dumb jointer question (maybe not so dumb)

teflon_jones

>Wow, I didn't expect so many varied responses to this question! It hasn't really helped me figure out what I want to do though since opinions seem split. Personally, I feel more comfortable with the handwheels so I think I'm probably going to go that direction.

So here's the models I'm looking at. Any feedback on which one you'd pick and why?

Grizzly: http://www.grizzly.com/products/8-Jointer-w-2-HP-Motor/G0586

Shop Fox: http://cgi.ebay.com/Shop-Fox-W1741-8-3hp-Parallelogram-Long-Bed-Jointer_W0QQitemZ310015202414QQihZ021QQcategoryZ67227QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

The Jet and Delta machines are out of my price range. Any other 8" jointers out there for less than $1000 (inc. shipping if not locally available to southeastern MA/RI)?

Re: Dumb jointer question

#10

Rick L

Re: Shop Fox is the choice!

Rick L

>The Shop Fox is the better of two. Can't figure out what your third choice is. Practice copying urls.

If you compare the bases of the Grizzly dovetailed ways jointer and the Shop Fox parallelogram base you can see the support is better on the SF. Also a parallogram jointer is superior in future adjustability unlike a dovetailed machine which can only really be shimmed.

As one who has serviced machines professionally, the Shop Fox is a better machine by far.

Re: Dumb jointer question

#11

Re: Dumb jointer question (maybe not so dumb)

Patrick Schupbach

>If I were buying a jointer,I would look at the GO490X. I own the original GO490 and its an awesome machine.It would be even better with the helical cutterhead!

Re: Dumb jointer question

#12

Pros/Cons of levers vs wheels

Mark Goodall - ATL - tooljunkie

>On a "regular" jointer, hand wheels and levers work differently to achieve the same thing (lift/lower the bed).

The benefits of the lever is that it's quick to move, but it's not as accurate as a handwheel.

The benefits of the wheel is that it's very accurate, but obviously not as quick and easy as a lever.

Therefore the best choice would be a jointer would be:

A handwheel for the outfeed table, because you want a very high degree of accuracy but don't change it very often so speed is not a concern.

And a lever for the infeed, because you adjust that all the time, but it really doesn't have to be nearly as accurate as the outfeed table.

The Delta DJ series (parallelogram) jointers, however, are compeltely different. Due to the design, they have managed to have a lever that give you the speed/ease of a regular lever combined with the accuracy of a hand wheel. Best of both worlds that only possible due to the parallelogram design.

Hope this helps.

Happy Woodworking!

Re: Dumb jointer question

#13

Rick L

Re: All paralleogram jointers have...

Rick L

>levers and they are all set up the same as the DJ20. Actaully the DJ20 is in the middle chronologically. The parallogram is of course from European design and Delta didn't invent anything here. Just a simple case of copying the parallogam design. Since then others, have jumped on the bandwagon like Grizzly, etc.

Our 20" parallogram RGA adjusts just as easily as a DJ20 or DJ30 and so does a SCMI parallelogram 16" jointer. The DJ20 is nothing special from the parallelogram crowd. They are are just as fast and as sensitive in adjusting.

Re: Dumb jointer question

#14

Re: Dumb jointer question (maybe not so dumb)

Hal

>I agree with Patrick in going to the Griz G0490 series. Don't know what improvements were put into the "X" model, but I'm very happy with my G0490. Don't know anything about the Shop Fox you're considering, but since it's a 3hp, I assume you have 220V available. I'd definitely upgrade to the 3hp. As I said earlier, the lever on the outfeed table is used only if adjustments to that table are necessary. Mine was on the money right out of the box and has stayed that way. Hope I never have to mess with it. Good luck. Hal

Re: Dumb jointer question

#15

Re: Dumb jointer question

Larry Clinton At Frankfort (Central)., Indiana

>I've owned and used both. My first joiner was a Grizzly 6" with levers. Can't say I ever wanted or needed hand wheel's when I used it - for about 15 years. When I upgraded to my current 8" Grizzly with the segmented carbide cutters, the machine had hand wheels, don't miss the levers - nor can I say the wheels made any difference in the use of the machine. In other words, I really don't care which as both do the job well. As far as the parallelogram design, I personally think it is very overrated. The dovetail design for raising and lowering tables has never caused me any alignment issues. All major industrial metal working machines, mills, jig boring machines (accuracy in millionth of inches) use the dovetail design. As an retired manufacturing / quality Engineer, I have seen and used this design for many years. I can see where the parallelogram design may be easier to produce and requires less precision in manufacturing due to the adjustment features. I mistreated my old joiner, but after 15 years of moving the unit by lifting it by the tables etc., it was still dead flat and coplanar (within .003"), when I sold it to a friend. Adjusting the gibs of a dovetail slide is not a big problem - even it it did get out of adjustment or wear (highly unlikely unless it was not manufactured properly).