Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

For those with Porter-Cable router tables (long) *LINK*

Posts

For those with Porter-Cable router tables (long) *LINK*

#1

For those with Porter-Cable router tables (long) *LINK*

Bill Houghton, Sebastopol, CA

>I've got an older Porter-Cable 698 router table, and have been frustrated with both the fence and the inserts around the bit.

I seem to have solved the fence problem with a Hartville fence (no affiliation, just a fairly satisfied customer; and it was on sale when I got it). I added T-track on each side of the table (track on top of aluminum angle stock, with the stock then bolted to the side of the table), and use that to hold the fence down. I found that, with the Hartville fence I had to get the T-track dead level with the table top, which turned out a bit challenging because the table edge, I discovered, slants. I wound up drilling and filing slots in the aluminum angle for fine adjustment; eventually, I'll drill some holes for roll pins to keep it in place. Were I starting over, I'd call Benchdog and see if they sell the fence for their contractor's table as a separate item.

My impression from the catalog pics is that the newer 698 tables have a far better fence than the piece of garbage P-C used to offer, so this may not be a problem. I've linked to Hartville's fence below, in case anyone's interested.

I decided I had to deal with the inserts around the bit after one of them bounced out while the router was running. No damage to the bit, and only some dings on the insert, but quite some damage to my peace of mind. I spent a while in spare moments thinking about how to fasten the inserts down and decided I needed a "collar" that would accept screws through the inserts. It seemed like a huge hassle, as I'd have to get the alignment just right, and, if I ever wanted the full diameter of the hole, for a panel raising bit, for instance, I'd have to flip the table over to remove the collar.

Then I realized: if I make the collar large enough to use the screws that are already holding the router base under the table, I don't need new holes in the table, and I can remove and replace it fairly easily. The picture below is the result. More pics and how-to's in the next messages.


img

Hartville's fence

Re: For those with Porter-Cable router tables (long) *LINK*

#2

Picture 2 and fabrication notes

Bill Houghton, Sebastopol, CA

>The collar is 1/8" aluminum, because that's what I had. It could be made of aluminum up to 1/4" (or, I suppose, even thicker - at some point you'd begin to lose depth of cut), and I imagine it could be made of acrylic or polycarbonate too.

Some dimensions:

Collar outer diameter 5-3/4� diameter, 2-7/8� radius

Collar plate hole 2-1/4� diameter, 1-1/8� radius (this is slightly larger than the hole in the largest P-C insert)

Screw holes for holding inserts down, size of circle, 2-5/8� diameter, 1-5/16� radius

Screw holes are tapped, 8-32 machine screw.

I used one of those self-centering center punches used for aligning hinges in the three holes in a regular router sub-base to make a light dimple, then made a better one with a center punch, and drilled the holes out. I got these holes aligned pretty well, but you could use slightly oversize holes - once the collar is clamped between table and base, it's not going anywhere.

The only really critical alignment is of the holes for the screws holding the inserts down. Here, I used the principle that the point-to-point distance of a hexagon inscribed in a circle is identical to the radius of the circle, and stepped off six points, then chose three for the holes. Were I doing it over, I'd use just two screws, on opposite sides; three is overkill.

You can kind of see the holes for the insert screws and for the router base at about 1:00 in the badly exposed picture below.


img

Re: For those with Porter-Cable router tables (long) *LINK*

#3

Pic 3 - the inserts

Bill Houghton, Sebastopol, CA

>I made a template for drilling the holes in the inserts, with a diameter identical to that of the inserts (3-1/6" diameter, 1-17/32" radius), then laid out a screw hole circle identical to that of the collar. I drilled leetle holes at each of the screw locations just large enough to accept the point of the center punch, clamped the template over a collar, and punched the screw locations. Then off to the drill press for drilling and countersinking (use oil).


img

Re: For those with Porter-Cable router tables (long) *LINK*

#4

Pic 4 - the collar in place, but no insert

Bill Houghton, Sebastopol, CA

>Just to be complete, here's the collar in place, before I put the insert in. I found that leaving the screws holding the router base on a bit loose while installing the first insert helped, as it the critical screw alignment - insert to collar - would self-align; I could then tighten down the screws holding router base to table, et voila!


img