Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

OT: Attaching 2x4's to poured concrete

Posts

OT: Attaching 2x4's to poured concrete

#1

OT: Attaching 2x4's to poured concrete

Dan Mitchell

>I posted a couple days back about the value of a used hot tub (as I suspected, turns out, "not much" ;-) We live on a wooded 1 acre lot, and the tub was located in an attached sun room. One reason I wanted to rip out the tub, in addition to our not using it, is rats were nesting beneath and around the tub & the steps up to it. Now that I have the tub out, I can see why it was so easy for them to get inside. The walls of the sun room are basically framed vertical wooden siding. As the pic shows, the trouble is the numskulls who erected the structure left large gaps between slab & these vertical boards. The picture is from the inside, on the other side of this wall there is either a deck or just the great outdoors. I'm thinking I'll run 2x4's, 2 high in spots requiring it, flat along the concrete to fill this gap. I'm wondering the best/easiest way (generally an oxymoron, I know... ;-) to attach the 2x4's to the concrete slab. The 4x4 uprights are attached to the slab with brackets, making it difficult to toe nail any such studs to them. I've seen those .22 load nail guns, which seem pretty quick & dirty, though I've never used one. Would one work well for this application? Helpful ideas appreciated!

TIA

Dan


img

Re: OT: Attaching 2x4's to poured concrete

#2

Re: OT: Attaching 2x4's to poured concrete

Nat Robison

>I like the powder-actuated nails for concrete. I used on a basement job after getting tired of trying the tapcons and wedge bolts. There are far fewer alignment problems with the nails.

I can't exactly tell from the picture but you might have a problem using them close to an edge. The potential is there to crack the surrounding concrete and blow out the edge.

You can pick up the nailer (the type you hit with a hammer), nails, and shells (for lack of a better word) at HD or Lowe's for $40-$50

Re: OT: Attaching 2x4's to poured concrete

#3

Re: OT: Attaching 2x4's to poured concrete

Clint Searl, at the base of Haycock Mtn

>The .22 nail gun is the way to go. I've used that approach to attach 2x's to slabs and blocks indoors and out with no problem. You can run a bead of construction adhesive under the 2x for extra sticking and gap filling.

Clint

Re: OT: Attaching 2x4's to poured concrete

#4

Re: OT: Attaching 2x4's to poured concrete

Barry Irby

>The powder actuated fasteners may be a good idea and easy, but they tend to be dangerous. Nat is right. If you shoot them too close to the edge of the slab they have a tendency to turn out and fly off like bullets. I have some old but vivid recollections of this. Did not get hurt, but it was very frightening.

If I were going to do this I would use treated wood and glue in addition to whatever fasteners I used. I would consider using a hammer drill and plastic screw anchors or Tapcon screws. Some sort of fasteners into the concrete, glue (epoxy or construction adhesive) and galvanized or stainless screws into the existing framing and siding. The three things together should hold fine.

Re: OT: Attaching 2x4's to poured concrete

#5

Re: OT: Attaching 2x4's to poured concrete

Dan Mitchell

>Thanks for the quick replies. Hadn't thought of the splitting issue, but I can see what you mean. If I were to nail in the middle of the 2x4, the edge would be about about 1 1/8" away. Could probably nail a bit more inboard, 1/4" or so. Adding construction adhesive is an excellent idea. I wonder if anyone knows if rodents find pressure treated lumber less palatable?

Thanks again,

Dan

Re: OT: Attaching 2x4's to poured concrete

#6

Re: OT: Attaching 2x4's to poured concrete

Dan Mitchell

>Thanks Barry, I've used tapcon before into block. Don't have a hammer drill at the moment, though I could probably get a HF one which would last this job anyway.

Why does EASIER always have to have some DRAWBACK?!? ;-)

Dan

Re: OT: Attaching 2x4's to poured concrete

#7

Re: OT: Attaching 2x4's to poured concrete

Mark Mandell - Gone Round In Jersey

>Hi Dan,

Powder-activated gun nails plus PL-4000 or equivelent are your best bet here. 2-1/2" nails in a firmly place gun should do you fine. DO NOT FORGET TO WEAR SAFETY GLASSES!!!! Keep your fasteners at least 2-1/2" away from the slab edge and at least 2" from the ends of the 2x. If you want to discourage chewing on the 2x, glue an "[" of aluminum flashing on the outside of your boards. Rats are pretty smart, they will remember their happy home and try to take it back, so the metal will stop them from the wood; just keep inspecting the outside surface for signs of attempts. You can also stuff some heavy/course steel or bronze wool in the old entry holes; they don't like its texture on their mouths.

mm

Re: OT: Attaching 2x4's to poured concrete

#8

Re: OT: Attaching 2x4's to poured concrete

Dan Mitchell

>Mark - Thanks for the reply, flashing's a great idea. The main trouble is there's about 12' of deck immediately outside the one wall where I can't see the outside. I eventually want to finish the inside with drywall, but I can put that off for awhile & observe for signs of entry.

Whoever thought decking was a good idea in a setting like this with all the trees (all the houses around here have them, probably most have rats too) must have worked in marketing for a pest control company. Might was well have a flashing red "welcome" arrow for the bloody rodents...

Dan

Re: OT: Attaching 2x4's to poured concrete

#9

If termites like to eat PT wood.....

Mark Goodall - ATL - tooljunkie

>... then my guess the rats would like eating it too.

I guess they aren't techically "eating" it as they probably don't digest it. I dunno really, but they sure chew it.

Happy Woodworking!

Re: OT: Attaching 2x4's to poured concrete

#10

Re: OT: Attaching 2x4's to poured concrete

JohnKJordan in East TN

>Sounds like someone first built a porch or patio, then closed it in, perhaps in a hurry.

I'm a fan of concrete expansion anchors instead of nails, but they may be overkill for this application. Nails work, but I often get chipping in the concrete, and the chance of knocking out the edge is significant. Anchors can be used relatively close to the edge - just drill holes in the concrete with a good hammer drill, insert the anchor, the 2x4 sole plate, and tighten nuts on the anchors. It would be nice to fasten the sole plate to the 4x4 posts with brackets or toenailed deck screws (toescrews?).

Does the right side of your picture shows one of the 4x4 posts, and if so, is it pressure-treated lumber? It's hard to tell in a photo, but if it is not PT and if it is deteriorated, you really want to get it up off the concrete. This can usually be done fairly easily if you brace the roof, cut off the bottoms, then slide in a sole plate underneath, around the entire outer edge of the room.

I would probably use construction adheasive on everything, plus the metal flashing. (Some people just glue the sole plate to the concrete instead of nails or anchors.) The rodents can chew through almost everything but the aluminum will slow them down some. Some extermination would help.

If the siding is deteroriating where it is close or in contact with the concrete, you might need to cut the bottom edge back a few inches, run an exterior band made from a 2x6 or so standing on edge on top of the 2x4 sole plate, then fasten the lower edge of the siding to that band. (I had to do this with 2x12s around the base of my 100 year-old pole barn where oak board siding had deteriorated.)

JKJ

Re: OT: Attaching 2x4's to poured concrete

#11

Re: If termites like to eat PT wood.....

Dan Mitchell

>Right, I was wondering if they find it distasteful enough to not chew through it.

Had termites in my last house in Ohio. Best story with them: the way they'd eat the PAPER off the interior surface of the drywall, leaving the PAINT in place!

Thanks for the reply.

Dan

Re: OT: Attaching 2x4's to poured concrete

#12

Re: OT: Attaching 2x4's to poured concrete *LINK*

Dan Mitchell

>Given that I want to present the most rodent-proof edge possible, I'm thinking I'll go with the hammer drill, since big chips out of the concrete will obviously lower the rat resistance. HF has one for $62 that looks like it would be capable of the limited use I'd likely put it to.

The posts aren't pressure treated, but the bottoms appear to be in good shape. I think the siding may be cedar, it also appears to be in surprisingly good condition. I do plan on using adhesive & flashing, perhaps 2 layers of the latter, it's cheap enough.

I am doing extermination as well. The gd things are also in the ~1400 sq' crawl space beneath the main house. I have 5 bait boxes around the perimeter of the house with a commercial grade one-dose poison, as well as 6 baited traps in the crawl space which I'm checking every couple days. I've trapped 2 so far. The poison was getting taken pretty quickly from a couple of the outside boxes at 1st, little activity since. I'm hoping this means the population is in decline. Either that or I'm knocking off all the local squirrels ;-) Judging from the amount of droppings I see down there though, it has never been toooo high. The crawl space problem at least has been addressed by 3 "professionals" that I am aware of (we moved in last April), none of whom have eliminated it entirely. I have found one entry point they all seem to have missed, I want to lower the population as much as possible before I seal it up. Hate to have them trapped down there & find there way into the house in an attempt to get out.

Dan


HF hammer drill

Re: OT: Attaching 2x4's to poured concrete

#14

Tapcon screws work great

Wayne

>

Re: OT: Attaching 2x4's to poured concrete

#15

Oh, come on now.......

Mark Goodall - ATL - tooljunkie

>Why does everyone always leave it to me to post these answers.

The right anwser is SDS.

And yes, I spent $400 (or whatever) on this to drill 4 holes. Of course, I've used it alot since then, but I deperately needed to drill 4 holes for a client and needed to look very professional.

Happy Woodworking!


img

Re: OT: Attaching 2x4's to poured concrete

#16

Re: Oh, come on now.......

JohnKJordan in East TN

>I bought a Bosch years ago and have never been sorry. As well as holes for anchors, I've cut out a drainage basin and channels for pipes in concrete, first drilling a series of holes, then using a chisel in the non-rotating mode to cut out the bulk. What a machine! (especially when compared to what the cordless drill makers call hammer drills.) However, for someone with just a few holes to drill a local rental place should carry this or something like it.

JKJ

Re: OT: Attaching 2x4's to poured concrete

#17

Where is "Tim the Toolman" when you need him

Wayne Carson "TX"

>

Re: OT: Attaching 2x4's to poured concrete

#18

More details, Dan

Barry Irby

>We go over this frequently but it never hurts to restate some of the details:

Treated lumber now is treated with ACQ and it is much more corrosive to steel than the older CCA stuff. This leads us to about three points.

Any treated wood you use this close to the ground should be treated for ground contact. I believe the above ground stuff is treated to .25 pounds per cubic foot and the ground contact stuff is .40. The Borgs often sell the lower content stuff. You may have to hunt for the ground contact stuff. If you shop around, you may be able to find lumber that was dried after it was treated, either Air Dried After Treatment (ADAT) or Kiln Dried After Treatment (KDAT). This material will be dryer, lighter in weight and easier to handle. and whatever adhesive you use will have a better chance of sticking to it.

Any nails or screws you use should be rated for contact with ACQ lumber. This includes those for Powder Actuated Guns. I am not sure they are available for the guns, but they should be. If you drive steel nails through wet treated lumber, they may very well rust away to nothing.

If you install the aluminum mentioned by others, you should use Coil Stock or the heavier gauge stuff made of rolling gutters. The chemicals in treated wood and soil will attack the aluminum. The baked on paint finish helps protect it. Don't use the thin shiny aluminum econo-flash.

Any wood near or in contact with the grade is an invitation to termites and rot. Consider replacing it with something like the aluminum coil stock or Hardie Plank material.

Re: OT: Attaching 2x4's to poured concrete

#19

The Tom Touch

Tom Dunlap

>A friend of mine ribs me about my over-complicated solutions to simple problems. She calls it The Tom Touch, ha ha.

If ground contact, decay and termites is a real concern I'd consider adding something to get the sill plate up off the concrete. Simple as cutting 3-4" blocks of treated material or as complicated as heavy steel tubing pieces. As I'm typing I came up with another idea. Cut rings of PVC to use as shims.

Re: OT: Attaching 2x4's to poured concrete

#20

Re: Oh, come on now.......

Garrett in Victoria

>I have the Makita rotary SDS drill. Only use it about 4-5 times a year, but when I need it... Oh yeah! Goes through anything like cheese.

Cheers, Garrett

Re: OT: Attaching 2x4's to poured concrete

#21

Jason Roehl in Lafayette, IN

I like that one, Mark...

Jason Roehl in Lafayette, IN

>..."I needed to look [emphasis mine] very professional." I may have to add that to my repertoire of tool-buying excuses. It's unfortunate, but sometimes, "looking professional" has quite the impact on a customer, but that perception does tend to vary widely.

Jason

Re: OT: Attaching 2x4's to poured concrete

#22

Re: More details, Dan

Dan Mitchell

>Thanks for that Barry. Your replies are always very informative and I'm sure I'm not the only one who appreciates them very much.

I've used one type of flashing on decks & elsewhere which is coated, seems to do pretty well.

The vertical timbers on this sun room have held up well since they were put in in 1993. Not that I want to follow one shoddy job with another, but frankly we're probably not going to be here all that long. If I actually had to replace all the supports, I'd probably just eliminate the structure all together. I want to do it right in that context, but my primary concern is keeping the rats out for the foreseeable future.

Dan

Re: OT: Attaching 2x4's to poured concrete

#23

Nah! A Porsche? *LINK*

Bri in Mtl

>Imagine what you'd look like with a Porsche....


Porsche

Re: OT: Attaching 2x4's to poured concrete

#24

Building codes rule

Derek

>Anything touching the sill plate or concrete floors needs to be pressure-treated. That is the answer. Same with dirt.

I'm pretty sure this is nation wide.

Also, there are building codes which specify the number and location of anchors and where to put them.

If you violate building codes, you might have insurance problems in the future if you do have a problem, not to mention problems selling the place.

Also, doing this without a permit may result in a fine if the local authorities find out. I have a friend who has this problem right now. A neighbor turned him in after a "difference of opinion". Everything was build by-the-book except for a few minor things but they were very unhappy...

I strongly urge you to find out what the building codes require and do it.

Re: OT: Attaching 2x4's to poured concrete

#25

Re: Building codes rule

Dan Mitchell

>Derek-I plan to use pressure treated for the 2x4's I add. The question originated over whether or not the existing uprights should be upgraded to PT. As far as I'm aware, building codes don't generally require that, or we'd all be tearing down our houses & starting from scratch!

Dan