Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

OTish: Material for Interior window trim?

Posts

OTish: Material for Interior window trim?

#1

OTish: Material for Interior window trim?

Ryan Stagg - Cincinnati

>Our new house has no window trim, and I'd like to trim them out in stool-and-apron.

Can anyone recommend paint-grade material for the trim and jamb extensions? I don't have much experience with this kind of construction material; would something like Windsor One be best? Pine? Lightweight MDF? It would all be simple '1 by' profiles, no curves. At least one window is 9 ft wide.

Re: OTish: Material for Interior window trim?

#2

Jason Roehl in Lafayette, IN

Re: OTish: Material for Interior window trim?

Jason Roehl in Lafayette, IN

>Pre-primed isn't a bad way to go, but there is a broad range of quality available. If you can see/feel the grain texture through the primer, don't bother, it's junk. One thing you might consider is that a squared-off 1x for a window stool will likely get dings and dents on the sharp edges. A bullnose (half-round) profile will look better longer. Also, if the window is fully drywall-wrapped, you should probably tear out the drywall and corner bead where the stool will go (you may not need to, but it may look funny, or there may not be enough height under the lifting "lip" on the window if that's what you have). Make sure you caulk the stool to the window jamb with a high-quality acrylic-latex or siliconized acrylic-latex after primer, but before finish paint. Otherwise, condensation (or rain if the window is accidentally left open) can get behind and under the stool and cause damage to the wood or paint in the long term.

Jason

Re: OTish: Material for Interior window trim?

#3

Finger jointed 1x poplar

Clint Searl, at the base of Haycock Mtn

>

Re: OTish: Material for Interior window trim?

#4

Re: OTish: Material for Interior window trim?

Barry Irby

>This very local in nature. Here in VA almost all trim is either pine (white or yellow or ponderosa) or MDF. Paint grade stuff is MDF or finger jointed. Stain Grade stuff is clear pine.

I hear that in other parts of the country the local practice is to use hardwood such as oak. That would be considered special order here and they would act as if it were custom made.

I also hear of poplar being used, not so much here.

Check locally on what is available.

Re: OTish: Material for Interior window trim?

#5

Poplar for paint. Yellow Pine w/o.

steve mackay

>

Re: OTish: Material for Interior window trim?

#6

Re: OTish: Material for Interior window trim?

George Koch

>Ryan, Here in upstate NY almost all new construction uses fj pine casings and flat stock if the finished trim is to be painted. George

Re: OTish: Material for Interior window trim?

#7

Re: OTish: Material for Interior window trim?

Jim Dillon

>Ryan,

I did all the interior window/door trim in a new addition to our cabin, maybe 13 years ago. I used reasonably clear 2x fir from the Borg, but this was because I was trimming a log interior and wanted something proud of the log wall. For regular interior walls, I probably would just use dimensioned 1x and 2x (sills) pine. Popular would be another choice for paint-grade work. I would spend a LOT of time getting good straight stuff, especially if you don't have a shop etc. This was before I had much of a shop, so I bought a portable table saw (Makita) to do all the ripping. I did have a SCMS to help with the crosscutting. A small block plane was useful as well as a scribe. It was a fun project and my first opportunty to use a TS so it was a real learning experience. The edge treatment of the sill is probably the most complicated. To help out, I picked up a couple of books that really helped me understand the process. I think the authors were Savage, and Tolpin. Good luck and have fun!

Jim

Re: OTish: Material for Interior window trim?

#8

Re: OTish: Material for Interior window trim?

NickB

>Windsor One is a great line of high end moldings, but if you aren't going high end (built up, large moldings), then you should be able to find what you need at a good lumberyard or one of the borgs (on the SF peninsula, there is a great door and molding place-I'm stuck with a lumberyard here in Eastern Mass).

If you can get good quality pre-primed MDF, I'd use that for casing material, but I'd go with poplar (or soft maple if you can get it at a reasonable price) for the window stools. If you can't get good preprimed MDF, look for good preprimed fj pine (if you can see the joints through the primer, it's not good fj material-no paint will hide joints that show through the primer). If the material is not backprimed, back prime before installation. If you can't find preprimed material, then see if you can find a source for clear pine.

I've been re-trimming the entire inside of my house, inluding replacing picture-framed window casings with stool and apron trim. I'm using 3 1/2 clear pine casing stock, which I mill into the trim I need (stopped fluting for the casing boards and a quirked bead for the aprons), and poplar for window stools, plinth blocks and rosettes. I use fj material where ever I can (saves money, and more efficient use of trees, particularly given that all of my new trim is paint grade).

I'm starting to see the end of the tunnel on my project-if we keep people out of the living room and dining room, the house no long looks like a construction zone!

Hope this helps,

Nick