Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Table saw upgrade question...

Posts

Table saw upgrade question...

#1

Table saw upgrade question...

David G. Sparks

>I'm trying to decide if I should go to the trouble and expense of changing my Powermatic 66 over from having a 30" extension table to a 52" one. I can do this for about $200. I mostly use the saw to prepare wood for small craft items, but I might want to make cabinets at some point. I recently built a dog house and was frustrated by the fact that I couldn't cut a piece of plywood in half. I have a Biesemeyer overarm blade guard that will have to be modified to work with the longer rails. I'll also have to make a wider table board. Do you guys think the larger crosscutting capacity is worth having, or should I stay with what I have? Thanks for your help.

Re: Table saw upgrade question...

#2

Re: Table saw upgrade question...

Stuart Hough

>If you're planning on doing casework at all, you'll eventually see the need for the longer work surface. Why wait till you experience the frustration again? You have a great saw...go ahead and build/buy the 52" setup! You can always change back to the shorter unit, if you don't get rid of it. I had a chance to ge a 52" railset and table for my saw, and waffled over the money...now I kick myself every time I turn on the saw (but this year's first Quarterly bonus will rectify that)!

Re: Table saw upgrade question...

#3

Re: Table saw upgrade question...

Bart Leetch

>I have an old right tilt Unisaw that I brought back to life & installed a 52" fence & scooted it so I could cut just over 24" to the left for a bevel cuts & the rest of the rail to the right.

If I was in your place I would go with a circular saw guided saw system like the EurekaZone (EZ-Smart System).

http://www.eurekazone.com/index.html

That is unless you plan on making cabinets all the time.

With the guided saw system you can take along if you should have an out of the shop situation. In the shop you can store it out of the way when not needed. You can't do that with a 52" fence & table system.

Even with my saw which has enough guide rail to the right of the blade to cut the ends of a base cabinet which is what I think your talking about I am going to get a guide system like this because my shop is small & it isn't easy to cut full sheets inside the shop without a struggle. Besides that even if you have enough room its easier to move the saw instead of the 3/4" sheet material.

I hope this helps give you another idea of how you can do the same job.

Re: Table saw upgrade question...

#4

JL

Re: Table saw upgrade question...

JL

>I bought the larger fence (50") when I bought my saw recently. Previously I had a contractor's saw with 30" rails.

I really like having the longer rails and the table. Unfortunately it is a horizontal surface - which means I sometimes have to clear it off before use :).

I also have a set of the Caio clamp guides (12", 24", 36", 50" and 100") that I use for cutting sheet goods. I really like those - that way I don't have to muscle a large sheet of plywood through the cabinet saw.

Re: Table saw upgrade question...

#5

Re: Table saw upgrade question...

Chad Pearson

>I have the 52 inch powermatic 66 with a nice roller extension table. Yesterday I cut up a sheet of cherry ply for some bookshelves for my 5 year old. Without thinking I reached for my Festool circular saw and guide rail to make the first cut (cutting down the sheet from 8X4 to 4X4. The Festool is a lot easier than wrestling a sheet of plywood through the table saw.

If I had to do it over again I would have bought a smaller table saw and purchased the Festool earlier. Keep in mind I am just a hobbiest, perhaps somebody that processes more stock than I would differ in their opinion. Personally I would take that 200 dollars and put it towards the Festool.

Re: Table saw upgrade question...

#6

Re: Table saw upgrade question...

David Sparks

>Thanks for all the help, guys. It's kind of a difficult decision, but I'm leaning toward getting the Festool system or some other saw guide to use on larger panels. Most of the wood I cut on my table saw is not very wide. It is difficult cutting large panels on my table saw. Thanks again for your ideas.