Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Bench top mortisers - - recent experiences ?

Posts

Bench top mortisers - - recent experiences ?

#1

Bench top mortisers - - recent experiences ?

Pete in Holland, MI

>Looking into purchasing a bench top mortiser. Have been looking at the JET, Delta, Steel City, and Shopfox. Am pretty impressed with what I see in the Steel City right now (especially with the price). I have experiences with hollow chisel mortising on my drill press, but think I'm straining the rack & pinion on the drill press.

Haven't seen any recent discussions on the machines, and am looking for what recent new owners have to say about their machines to guide me in my purchase.

Thanx !

Re: Bench top mortisers - - recent experiences ?

#2

Re: Bench top mortisers - - recent experiences ?

Jesse Cloud

>Benchtop mortisers are safe, quiet, and IMHO fun to use. They can make deep mortises. They don't, however, make as clean mortises as a router does.

Accuracy can be an issue, too. Lots of folks hook up some sort of modified X-Y vise to hold the workpiece.

I have a powermatic and find myself using it less over the years, half way thinking about sellng it.

If you get one, be sure the chisels are sharp and take your time to align the chisels dead parallel with the fence. Clean up after each cut- they make a lot of shavings and a shaving between the workpiece and the fence will cause troube.

Re: Bench top mortisers - - recent experiences ?

#3

Re: Bench top mortisers - - recent experiences ?

Jay St. Peter - SoMD

>I got the PM benchtop and just recently used it for the first time. It worked well, but I have no real base of comparison except for other methods. I got it cheaper than most of the competition, but not sure what the prices are relative to the others these days. There were deals going on when I got mine. It's nicer than some of those you're considering due to the fence design. The downside is no included chisels.

Jay

Re: Bench top mortisers - - recent experiences ?

#4

Wanna buy mine?

Mike Schwing from Maryland

>I have no use for it as I've learned to chop my own faster than I can do so with the Jet mortiser. It works fine, but the time it takes for setup and then to clean the mortises thereafter is longer than that which I can do them by hand. In the event I don't want to do that, it is faster to use the router than the mortiser.

Its a heavy thing, so I'll sell it locally.

Re: Bench top mortisers - - recent experiences ?

#5

Like The Shop Fox Very Much

George@Colonel's Workshop

>Good Afternoon Pete,

I went thrugh the same quandry three years ago or more. I was able to test drive the PC, Jet, and Fisch. These all worked very well, although I definitely favored the Fisch's somewhat smoother operation. That could have been chisels. After more thought, I decidsed on the Shop Fox #W1671. I ordered it on line and had it delivered within 36 hours! It had greater capacity and capability than the others I had tested, and the motor was 3/4hp. It was supported on stout dual posts, could be rotated on its base to mortise off the table if needed, and the handle was adjustable. I came with a standard fence/hold down arrangement which I replaced with a cross slide vise from Harbor Freight. You need one of those critters for sure. If the mortiser you select has one, great! If not, buy an inexpensive one one ($50-$60)from HF or Grizzly. You can align the chisels with the lay out marks, crank and pull, and the mortise is done. I bought a set of Fox Shop chisels and they have satisfied my non-commercial needs. It was a very good decision, and I'd buy it again.

George

Re: Bench top mortisers - - recent experiences ?

#6

Re: Bench top mortisers - - recent experiences ?

Larry Clinton At Frankfort (Central)., Indiana

>I have a Fisch, it is the 3/4 hp unit with the 1725 RPM drive. I really like my unit. It came with the GuideCraft chisels, They have worked very well, although I did bend the 1/4" chisel. I straightened it and it works perfectly. I am finishing a blanket chest which has about 50 M&T joints - 16 or so are though tenons - all fit very well. I did build an auxiliary fence and hold-down. I have a cross-slide vise I intended to use, but my present setup works very well and I believe is faster. Setup is critical as some has mentioned. When setting up my unit, I clamp a straight edge to my chisel and use a digital caliper to align the straight edge to the fence.

Re: Bench top mortisers - - recent experiences ?

#7

Re: Bench top mortisers - - recent experiences ?

Jeffrey D. Rose

>I have a General and I don't use it often, but sure like using it when I do. It came with a good set of chisels and strong fence. I bought it off someone that worked at the Woodsmith Store and got it with a employee discount but never used it, so got a deal otherwise we have a Delta at work that isn't worth the metal it is made of. I recall the Jets and the Fischs were good for their price when I was looking, but came across teh General and couldn't pass it up.

Jeff in Iowa.

Re: Bench top mortisers - - recent experiences ?

#8

I bought the Powermatic PM701...

Mark Harrison - Brisbane, Australia

>I'm quite happy with it. It has plenty of power and the fence and hold downs actually work. Down side is you don't get any chisels but most of us usually only use one or two sizes anyway.