Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Need help ASAP:Jointer

Posts

Need help ASAP:Jointer

#1

Need help ASAP:Jointer

Todd

>I'm stuck. I'm trting to glues up some pamels but I can not get the joint of the 2 boards to be tight (the cut on the table saw does better than the jointer.....). The knives are set to the same heigth as the out feed table. I am keeping pressure on the outfeed side to hold the board to the table. The infeed and out feed tables are approximately 33" long and the boards that I'm jointing are 72 inches long. The jointer is putting a bow in the middle of the boards (i.e. when the 2 boards are put together and touching in the middle, there is a gap on each end). I can make this gap bigger by removing more material on the jointer (deeper cut). I have taken a striaght edge, placed it on the outfeed table and measured a .020" difference in the infeed table (.000" at the blade then going to .020" at the start of the table). I do not know if this causes the problem but if so, I do not know how to adjust the infeed table to make it parrel to the outfeed.

I tried moving the outfeed table higher with respect to the blade. When feeding the board through, I would get half way through and then the jointwe ws not cuttng the board any more (actually raised the infeed side of the board off the table

I need to fix this issue ASAP so any ideas on what to check and measure would be great........

I have the Delta 37-380 8" professional jointer (not the DJ-20 8").

Re: Need help ASAP:Jointer

#2

Check the end of the out feed table

Dustmaker Mike

>I would check the outside end of the outfeed table and see it is level with the knife end. Same for the infeed table. That is a guess and I am sticking by it until someone smater and better looking comes along and proves me worng.

Re: Need help ASAP:Jointer

#3

Re: Need help ASAP:Jointer

waroland

>Outfeed table should be even or slightly below the knives. If the tables are not coplainer (level with each other) that will cause the problem you have. If you have a book, it should show you how to set the infeed table correctly.

Re: Need help ASAP:Jointer

#4

Re: Check the end of the out feed table

Todd

>How would I do this? If I lay a staright edge on the outfeed table and align the blade to it, doesn't this accomplish the same? From this thou, I do not know if the table is would be tilted.

Maybe if I level the outfeed table by means of shiming the whole jointer, then measure the infeed table relative to the level line, this might work?????

Re: Need help ASAP:Jointer

#5

Re: Need help ASAP:Jointer

David Yoho

>Both the infeed and outfeed tables of that jointer are 35 7/16" long. The total length is 72 9/16". That jointer is more than capable of jointing stock the length you have. I have mine set most of the time to cut 1/32" deep.

Here's what I'd do - get out the manual and go back over the setup instructions. Check out all the infeed/outfeed settings to confirm you're good there and make sure the cutterhead is set properly to the outfeed table.

If the jointer checks out, try straightening your bowed stock by placing a straight piece of something you have around the shop from one end to the other. Run a pencil down the edge so you can see the "high" spot. At the jointer, start your cut where the pencil line begins by dropping it onto the cutter and only run it to where the line stops. Do this until the line is gone. Then try running the entire length several passes and check the edge. If you're feeding it right and the jointer is setup right, you should have a straight edge.

Another thought - don't discount the idea of some stress in your wood being released causing you this heartburn.

David

Re: Need help ASAP:Jointer

#6

Re: Need help ASAP:Jointer

Moses Yoder in White Pigeon, MI

>If the actual measurement of .020" out of plane over 66" is correct then I doubt that this is what is actually causing the problem, although it would contribute to it. As mentioned, get the manual out of the wastebasket to adjust the tables. I think your outfeed table might need to be set a hair lower. You want to set it just low enough that you are not getting snipe on the end. To joint long boards straight you will need to learn where and when to put pressure on the board. If the board is already bowed out in the center, take cuts out of the center portion only until both ends touch the table. Then take one long pass the entire length, as mentioned previously. Also you do not mention how much gap you are getting. Ideally you would have about 1/16" gap in the center of a 72" log panel when you clamp it together so the ends are not as apt to split. If you ahve 1/16" gaps on the ends, you can press it together with a clamp but it is not good craftsmanship. A good option would be to buy a Lee Valley #7 jointer plane and learn how to use it.

Re: Need help ASAP:Jointer

#7

Outfeed table set too high

Grant in Iowa

>Todd,

I have the same jointer and I find that the right height for the outfeed table is about .002" lower than the knife at TDC.

Read my post below about how to check this and the knives for same height with only a steel ruler. (in response to another jointer issue). This is what I do and I can get 6' pieces of lumber arrow straight out of my 37-380.

Basically, lower your outfeed table slightly, rerun the piece and a mate for it. Then readjust as necessary. Lower the table to get rid of a convex edge, raise it to get rid of a concave edge. Slide two workpieces over each other end to end to determine which one is at fault.

Regards,

Grant in Iowa

Re: Need help ASAP:Jointer

#8

a common problem, easy fix.....

Bill Tindall, E.TN

>You have a common problem and it likely has nothing to do with your jointer or technique. I will call a board that is fat in the middle convex and one that is skinny in the middle concave.......

It is easy to get a straight edge on a convex edged board. The jointer mows off the leading edge and the back edge stays flat on the bed until it passes and then gets mowed off. Eventually after a pass or two the board is straight.

Convex edges on the other hand are very hard to straighten on a jointer, especially so one as long as you are trying to do. The cut tends to follow the curve of the edge in spite of one's best efforts and the edge stays convex and likely gets worse.

I sight every board and joint the concave edge. If the other edge is more then 1/8 to 1/4" convex (fat in the middle) I will run the board through the table saw to make this edge parallel to the jointed edge. Then I run the edge through the jointer to remove the saw makes.

Alternatively, there is another way to straighten a convex edge. Start the leading edge of the board up on the outfeed table and run it through. What will happen is that the leading edge will not cut because it is up on the outfeed table. The middle of the board will get cut. The trailing edge may not get cut either because it is already more narrow than the middle. Now think what happened- the middle of the board just get more narrow, just what you wanted to happen. I keep repeating this operation until I get a cut that goes all the way to the trailing end. Then I take one additional clean up pass full length. This approach will remove a convex edge but it is slower than sawing it out.

Re: Need help ASAP:Jointer

#9

after 3 hours of messing

Todd

>I have now mananged to make saw dust worth about 2 inches of broads. I can not fix the problem.

I have tried many of your responses but I'm still at a loss. I have placed shims under the infeed table in order to make it more Co-planer to the outfeed table. I have rasied and lowered the outfeed table with all the results that everyone has mentioned. I have set the out feed table to so that a ruler is moved about an 1/8". The results when taking 2 boards an putting them together is not desireable. I do not have feeler guages therefore I do not kow what the gap actually is other than it is visible and I can rock the boards back and forth by squeezing alternate ends together. I similar size gap in the middle would be ideal and I would just glue up.

What concerns me the most is when I rip the 2 boards on the table saw and put them together, they produce a better joint than after I run them through the jointer.

I'm about ready to give up on the jointer and send the boards through the planer on edge. I figure if I clamp 3 or 4 boards together on edge and send them through, this would produce a better joint......

Shorter boards are easy, it the long ones that are creating the problem which leads me to think it is my technique.

Well, I will try for one more hour tonight then determine what to do tomorrow.

Thanks for your help. If there are any other ideas, please let me know...

Re: Need help ASAP:Jointer

#10

Re: after 3 hours of messing

Mark Rakestraw

>Todd,

I understand your frustration in not being able to set the machine up for perfect joint. But if you're talking about needing feeler gauges to measure the gap over a six foot length you don't have a problem. If you enjoy tweaking machinery to get things perfect, and many people do, keep at it. If you'd prefer to be woodworking, glue up your panel and get on with it.

Mark

Re: Need help ASAP:Jointer

#11

Re: Need help ASAP:Jointer

boardman

>This is pretty common on long stock, and in my experience 2 things cause it:

1- lack of support on the leading end. By the time you get to the end of the board, the front end is hanging way off the outfeed table. Although you think you're holding it even, the weight seems to invariably cause the front end to droop down. If you had an outfeed table as long as the board, or roller stand set to the perfect height, this wouldn't happen.

2 - It's a lot easier than you think to flex a board across it's width. The downward pressure is at it's worst on long stock just because you're probably putting a lot of pressure on it to compensate for the leading ends weight.

And running the board thru again only increases the "bow."

Short of an extra supprt for the leading edge, I've corrected this problem the old-fashioned way. Get out the straight edge and power plane and ROS sander. I was going crazy trying to get some 1" x 9" x 80" oak straight until it fixed them with this method. Gets it straight enough the clamp pressure closes it up.

Re: Need help ASAP:Jointer

#12

My 2 cents

Lee Schierer - McKean, PA

>If your edges are straight after ripping and your saw is tuned up so that you don't see radial saw marks along the edges, then they are probably true enough and clean enough to glue up without jointing. I used to do this before I came to own a jointer and none of the joints have ever failed. If the mate up nice without gaps after ripping you can avoid the jointer problem for now and get on with the project.

It does sound like your jointer tables are out of adjustment. From your initial description, it sounded to me like your out feed table was drooping at the outfeed end. You should be able to see this by taking a straight edge or straight board and raising the infeed table so the edge closest to the cutter head is exactly the same heigh as the front edge of the outfeed table. Rotate the cutter out of the way. Place the straight edge on the infeed table and slide it across to the outfeed table keeping all the pressure on the infeed table. When the end of your straight edge reaches the end of the out feed table you may see a gap. This means the outfeed table needs raised up only at the outer end. How you make that adjustment depends on the construciton of your jointer.

Lee

Re: Need help ASAP:Jointer

#13

An additional pennies worth

Lee Schierer - McKean, PA

>When I adjusted up my jointer I used a 4' level for a straight edge. If you don't have one, borrow one or buy one. They are great to have around.

Lee

Re: Need help ASAP:Jointer

#14

Today's update

Todd

>Basically I have left the jointer behind. I put a new blade in the table saw and set up my power feeder so that the boards get fed at a consistant rate. The joints are much better than on the jointer. There are no saw mark, therefore I hope I am getting a good joint.

I have glued up 4 panels 24"x72" and have 11 left (maybe I should try breaking one of them apart before I get too many made.......

I will tackle the jointer again once I have a real good straight edge. (using the 3 different levels I have makes it even harder to figure out the true issue). I believe the issue is with the 2 table not being co-planer.

Thanks everyone for your inputs, its great to get ideas, opinions, suggestions and clarifications in such a short amount of time.

Now back to making doors..........

feeds consistently

Re: Need help ASAP:Jointer

#15

Try a Master Bar

Rod Peterson -- Ormond Beach

>Here's an article from the WoodCentral Articles section which describes how to build a Master Bar for just such alignment. I found it was necessary to read it two or three times to digest the concept employed, but once I did, it was very clear.

Rod

Re: Need help ASAP:Jointer

#16

Re: Today's update *LINK*

Grant in Iowa

>Todd,

I suggest you check with a local industrial flooring supplier and get a flooring straightedge.

I have one of these 6' long and LOVE it. Straight to within .005", and made of spring steel with a ground edge. It allows me to decide which of two boards isn't straight, set up machinery, and so on. Most of the machinist straightedges aren't long enough for this, IMHO.

Check the link below to see what I'm talking about. The link is just something I googled up, so find your own source. Not cheap to ship, so try to find one locally.

FWIW,

Grant in Iowa


Flooring straightedge