Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

sniping on jointer

Posts

sniping on jointer

#1

sniping on jointer

Wayne

>Need some help and advise on Grizley 6" jointer. When running a board through it is sniping the last couple of inches. I checked the the outfeed table and after runninbg about 12" through it is a few 1000" lower at the blade than at the toe. Is this what is called not co-planer?? If so is there a fix for it?

Re: sniping on jointer

#2

Re: sniping on jointer *LINK*

Paul Cates - Henderson, KY

>Hi Wayne,

If you're getting snipe, then raise your outfeed table to the same height of the knives, or maybe just a hair below the knives. Co-planar means that both tables are in the same plane. If the tables are not co-planar, when you place boards edge to edge, you'll either have a gap in the middle or at both ends depending on whether the tables are low next to the cutterhead or low on the ends.

The link below might help.

PC


How to tune a jointer

Re: sniping on jointer

#3

Re: sniping on jointer

Grant in Iowa

>Wayne,

Unplug the machine and check your setup:

-Take a steel ruler or similar object (you can use a straight board, just make a mark on it so you always start from exactly the same point). Stand it on its edge and place it on the outfeed table such that the 2" mark precisely aligns with the edge of the outfeed table adjacent to the cutterhead. Rotate the cutterhead by hand in the normal direction. The knife should pick up the ruler and move it between 1/8" and 1/4" as it goes by top dead center. Check each knife at each end and they should all move the ruler or board about the same amount...within a 16th of an inch or so.

-If this test is causing your ruler to move more than 1/4", RAISE your outfeed table. If the test causes your ruler to not move at all, then lower your outfeed table to bring the amount it moves to about 1/8". This 1/8" usually means your outfeed table is about .002" lower than your knives, which I find to be about right. Note that if the readings vary widely, then you need to adjust the knives individually. Indeed, this method is what I use to align the knives when I change them out at sharpening time. Fast, works good, and no need to buy fancy jigs.

If you are having a gap form beneath your workpiece during a cut, then I think the first thing to check is the outfeed table height. If you are having trailing edge snipe on your workpiece, then raise your outfeed table and make test passes to tweak its height until you get no snipe.

Also look closely at the "planer" marks on your workpiece after a pass. They should be evenly spaced, and if they aren't, your knives need adjusted.

Another possibility is technique. As you feed work into the jointer, you must not apply too much downforce to the piece while it is on the infeed table, and certainly not enough to bend the workpiece. Once the work makes it to the outfeed table, make sure it is held on the surface of the outfeed table. You can use plenty of downforce once the work is on the outfeed table (assuming you aren't working with a badly warped piece, needing additional passes).

You can also check the coplanarity (is that a word?) of the infeed and outfeed tables by laying a long straightedge accross the top of the jointer and raise the infeed table to very close to the straightedge. You can then tell either by eye or with a feeler guage how far out of planar the two tables are. Check your owners manual for adjustments, or call Grizzlys tech support line.

Hope this helps!

regards,

Grant in Iowa

Re: sniping on jointer

#4

empirical fix

Bill Tindall, E.TN

>raise the outfeed table until it doesn't do this any more. There may be complicated reasons for the problem you describe but a too-low outfeed table is by far the most likely. It is sniping because the board is dropping off the infeed table onto an outfeed table that is lower than the top of the cutter head.

I don't know about your jointer but if you can't raise the outfeed table then you must lower the knives, which is about 100 times more difficult to get right. It is enough to make one buy a jointer with an outfeed table that adjusts!

Re: sniping on jointer

#5

Re: sniping on jointer

FredD

>jointer snipe,

In addition to all of the helpful suggestions you recieved on your GRIZZLY jointer , if one of them did not rectify the problem, you may have a warped infeed or outfeed table which is easily determined by a competent machinist and if that is the case you may find the fix not worth the expenditure and ask GRIZZLY to replace the table or tables or machine. Asking their tech support to diagnose the problem over the phone is kinda like the tv ad where the guy needing major sugery is getting directions from his doctor over the phone.Lots of luck.

FredD