Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Spray finishing texture

Posts

Spray finishing texture

#1

Spray finishing texture

Brian Aust - Nevada, IA

>I am refinshing a guitar body, I used vinyl sealer for a base then nitrocellulose lacquer with tint for color, then clear for a topcoat. This is my first time using a spray gun so I'm not sure what the texture is supposed to be. I thinned the last coat, about 20% I'd guess. My finish isn't glass flat, I don't think you'd call it orange peel but it's going to take a bit of sanding before I can buff it. I'm wondering if this is normal or if I need to adjust something when I'm spraying. Now I wish I'd taken those shop classes back in high school.

Re: Spray finishing texture

#2

Re: Spray finishing texture

Clint Searl, at the base of Haycock Mtn

>You may be able to salvage things by spraying misting coat(s) of almost pure reducer to melt back the top coats so they will self level. I sometimes do this as part of my gun cleaning routine.

Overall, I think you made the process too complex. Throw out the vinyl sealer; it serves no useful purpose. Tint with either a water soluble aniline dye stain first, or tint the clear lacquer with a compatible aniline dye stain. Eliminate the NC inter-coat and just use the final finish. I get great results with Sherwin Williams alkyd lacquer in either high gloss or medium rubbed sheens, depending on the application. It's self-sealing, tintable, and produces a nice finish that needs little rubout.

Clint

Re: Spray finishing texture

#3

Re: Spray finishing texture

Mark Mandell - Gone Round In Jersey

>Brian,

The usual causes of a "bumpy" spray finish are that your gun is not properly atomizing the material and/or your finish is drying too fast.

Regarding the gun, you want to check to make sure your tip and set up is correct for what you are spraying; pushing solvent lacquer through a tip sized for heavier waterborne finishes can give you issues. You haven't mentioned the gun type, so it would help to know what you're spraying and how you have your gun set up.

Regarding the finish, it sounds like you may need to retard your finish to allow it to flow out and level better, but before you go there, post more about your equipment.

mm

Re: Spray finishing texture

#4

Re: Spray finishing texture *LINK*

Brian Aust - Nevada, IA

>The link will show the spray gun I have, I haven't found the brand name on it anywhere so I assume its a no name Chinese gun. Does the temperature at which you spray nitro make a difference in the flow? It was usually below freezing when I was spraying.


spray gun

Re: Spray finishing texture

#5

Re: Spray finishing

Mark Mandell - Gone Round In Jersey

>Ok, that helps, as we can rule out a turbine HVLP that's heating/drying your finish before it gets to the surface.

Can I assume that you're working at no more than 50 PSI (the usual limit on that gun type)?

The most common mistake with lacquer is staying too far away from the surface. You should adjust your aircap for as wide a fan as you can do and then stay not more than 6" from the surface during application. Since you have a siphon gun, open your material knob a bit more and work side-to-side moving away from you with the gun at as steep an angle as you can with a 50% overlap of the prior pass. The further way from the surface you get, the more time you give the solvent to flash off before it gets to the surface which then inhibits the resin's ability to flow out and level. Don't try to empty the gun before adding more product; your siphon feed should work better with the cup over 1/4 full, and make sure that your cup vent is clear.

Now to the finish. Have you sanded your base costs smooth? If not, their texture will telegraph into your topcoat. I can't say that I've ever tried to apply finish in below-freezing temps. I'd suggest you get some heat into the space. It will certainly have an effect on how the film sets up; ask your finish supplier (paint store) if they have a recommendation for an additive to assist in flow-out and leveling of the film under the conditions in which you're working. Do not, however, apply warm or room temp finish to a freezing surface; you're likely to get a lot of blush condensation.

I'd strongly suggest you set up some practice boards or surfaces, and try to work things out that way. Remember, a piece of cardboard will work just as well for a test piece.

Hope this helps.

mm

Re: Spray finishing texture

#6

Low temp

Ed Mulligan, Cape Cod

>Does your surface feel like fine sandpaper?

I once tried spraying nitrocellulose lacquer at a low temperature. Temp was in the 40 to 50 degree F range. The dry surface had a sandpapery feel to it. When the spray booth warmed up, the problem went away.

Ed

Re: Spray finishing texture

#7

Re: Low temp

Brian Aust - Nevada, IA

>It does feel a little like sandpaper, it was about 15-25 degrees when I was spraying. We put on the sealer when it was nice out but the cold spell caught us and I didn't want to wait until spring to get it done.

Re: Spray finishing texture

#8

Re: Spray finishing

Brian Aust - Nevada, IA

>My pressure was set about 55-60 psi at the outlet of the tank and I'm using about 40' of hose. I think you're right about the distance I'm spraying from, I noticed that when I did the edges of the body I would set the fan to narrow but get closer and the finish was much smoother. I'm having good luck wet sanding with 320 grit paper, besides, I'm out of nitro so I can't spray any more and I don't want to buy another quart just for one coat. I would like to practice, so if I do another guitar I might buy more than I need and do some test spraying.

Re: Spray finishing texture

#9

about temperature and vinyl

Michael Dresdner

>Yes, temperature is critical in lacquer flow out. If you want to see marked changes in lacquer, simply warm it. Rules of spraying say that the wood, finish and air should all be at the same temperature and should all be at or above 70 degrees. If that is not possible, at very least make sure the wood and lacquer are as warm as possible. You can then take them out to spray, and bring them right back the second you are done spraying. Get the lacquer up to 80 degrees and you will see marked improvement in flow out.

Most lacquers these days are sold too thick for most spray situations, so you would benefit from substantially reducing the lacquer with thinner. Don't hesitate to reduce it fifty percent or more. There is no harm in that and it will make your job easier.

Don't set the fan too wide -- set it to where you get the best saturation throughout the fan. Spray with the gun about eight inches from the work. If you are not a skilled sprayer, practice on cardboard, not guitars.

As for whether or not you need vinyl sealer, it depends largely on what the guitar is made of. In the industry, vinyl is used to adhere to some of the synthetic plastic bindings, particularly the ones Martin uses, and to prevent rosewood from bleeding onto adjacent binding. If you are using cellulosic binding and not using rosewood, there is no real need for it. Incidentally, dewaxed shellac (Zinsser SealCoat) does the same two things and is much less problematic than vinyl.

Re: Spray finishing texture

#10

Re: about temperature and vinyl

Brian Aust - Nevada, IA

>Thanks for the replies everyone, I guess I'll do my next guitar in the summer, or wait til I get heat in the shop.