Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

kitchen cabinet finish

Posts

kitchen cabinet finish

#1

kitchen cabinet finish

les winter

>I'm starting on building kitchen cabinets. It looks like furniture grade maple ply is available in my neighborhood. Door and drawer fronts to be hard maple.

I don't spray, and I'm going to have a lot of realestate to cover. I'm leaning towards poly, but I've never really liked it. Any suggestions would be appreciated.

thanks

Les

Re: kitchen cabinet finish

#2

Re: kitchen cabinet finish

Joe in a Cleveland suburb

>Les.

Disclaimer - I am not an expert. Just a weekend woodworking hack.

A few years ago I built my kitchen cabinets using cherry and cherry ply. I used poly that Jeff Jewitt sold to me (his shop is about 4-5 miles from my home). I brushed it on. Multiple coats. Sanding, sanding, leveling, sanding... then rub them out and wax. All the doors, face frames, and so on. I would not recommend this to my worst enemy.

The cabinets need to be refinished already. Waxing them was pretty dumb. The wax looked and felt great. For about a week...

I should have checked here first for better ideas. Also, I should have explained to Jeff what I was doing. I was having problems getting a nice finish. I took a cabinet door over to Jeff and he should me how I should be brushing on the poly, sanding it, rubbing it out, waxing and so on. He later told me had he known this was for an entire kitchen, he would have suggested a different method.

I am telling you this just so you know brushing on poly (or wiping - I tried that too) is a pretty big effort. At least to me it was.

If I were to do it again, I would definitely look into a low cost sprayer thingy.

Joe

Re: kitchen cabinet finish

#3

Water borne poly floor finish

Clint Searl, at the base of Haycock Mtn

>Or water borne one-part epoxy.

Clint

Re: kitchen cabinet finish

#4

a new wrinkle

les winter

>This is from the ask and you will receive department. Just yesterday I got my Fine Woodworking and there is Norm on the front cover with kitchen cabinet tips. He recommends pre-finished 3/4" maple ply for the interiors. I've never heard of prefinished. Anyone else have?

thanks for the replies

Les

Re: kitchen cabinet finish

#5

Prefinished Maple Ply

David Yoho

>Yes, but you won't find it at the Borg. Check with your local cabinet shop supplier. They will either have it or can get it for you.

David

Re: kitchen cabinet finish

#6

Re: Prefinished Maple Ply

les winter

>excellent. thanks

Les

Re: kitchen cabinet finish

#7

Re: kitchen cabinet finish

Chrispy

>Les, when I built new doors for my kitchen cabinets from Red oak, I finished them with a wiped on 50/50% mixture of Tung oil and Helmsman Poly spar varnish. Went on easily, one coat only, and looked great leaving a very slightly shiny finish. When the doors get dirty, I will clean them and apply another coat. Regards, Chrispy

Re: kitchen cabinet finish

#8

Re: Prefinished Maple Ply

Glenn Madsen near San Francisco

>I bought a couple of sheets Wednesday morning for a project from the local plywood supply place. (Oakland, CA) About $60 each for certified, made-in-the-USA, 3/4" maple, at least C2 grade, water-poly finished. I've been buying there for years, as a hobby guy, and never spent more than $500 in one trip, for volume pricing comparisons.

I thought we got a good deal on good stuff at small volumes.

Re: kitchen cabinet finish

#9

Re: kitchen cabinet finish

Joe Dusel (Vista, CA)

>I agree on the pre-finished plywood. The one caution is to make sure that you buy the American made products. The Chinese stuff looks great on the surface but it is loaded with formaldehyde and does all kinds of tricks (bowing, cupping, delaminating) when you cut it.

Joe