Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Mounted Power Feeder on Jointer (w/pics)

Posts

Mounted Power Feeder on Jointer (w/pics)

#1

Mounted Power Feeder on Jointer (w/pics)

David Eisan

>Hello Everyone,

After a three month wait, my jointer power feeder made its overseas journey successfully, arriving at work a couple of weeks ago. Work on the house has held up its installation until tonight.

I assembled the main components and laid them out to see what needed to go where,


I drilled and tapped two holes in the back of the jointers main casting to receive the mounting bracket. It wasn't until after I had drilled the holes that I noticed that I would not be able to swing a regular tap handle for the hole nearest the fence mounting bracket. I didn't feel like removing the fence so I used a 12 point 1/4" box end wrench, and with many 1/2 turns, I had both holes tapped,


Time to mount the power feeder,


I have it so it is pulling just after the cutterhead. I feed the board about 6" past the cutterhead and the power feeder takes over.

I noticed right away that even with the turtle/hare speed selector in turtle mode, the power feeder was going to be running too fast. I switched out the primary set of gears for a second set that would allow it to run even slower,


Time for a test run,


I was not sure what to expect for marks on the back of the board from the power feeder; and I was happy to see virtually none,


Here is what the business end of the power feeder looks like,


I only ran the one test board tonight, but I am quite pleased. I have 1200 BF of cherry to turn into cabinets and trim around the house, this should make it easier.

Thanks for looking,

David.

Every Neighbourhood has one, in Mine I'm Him

Re: Mounted Power Feeder on Jointer (w/pics)

#2

Re: Mounted Power Feeder on Jointer (w/pics)

Wayne

>what brand is it and where did it come from?

Re: Mounted Power Feeder on Jointer (w/pics)

#3

Re: Mounted Power Feeder on Jointer (w/pics)

Keith Newton------WebKitFormBoundaryDZmgloT+ZiYFgX

>I am guessing that is a 12" jointer, and wondering what the HP of its motor is? I have a 12" which had a 3 HP motor on it when I got it, and i used it that way for a long time, before changing it to a 5 HP a few years ago. But then I sharpen the knives with a face bevel, which reduces my cutting angle to ~ 10�, which requires a bit more power than the 30� angle of attack of the knives mounted in the head.

I sure like having the extra power now, and only commented because you mentioned having to slow the feeder down, so you might have that for comparison if you had thought of raising the power on the jointer. I know there are other factors like number of knives,mine has 4, and cutting circle diameter, RPM's etc. which affect the need also.

That looks like a great set-up, you have now got me wishing for a feeder to put on mine. My hands are not as strong as they once were, and feeding a big plank over these tools needs all I have go, not to mention the pain.

I would like to know the brand and model # also. Thanks for the post.

Re: Mounted Power Feeder on Jointer (w/pics)

#4

Steel blades instead of rubber wheels?

Mark Goodall - ATL - tooljunkie

>I see that the pressure feeder uses steel blades instead of rubber wheels. Did you choose that because the top face of the lumber will usually be rough sawn, and you only do one face on the jointer and use the planer to do the other face?

Happy Woodworking!

Re: Mounted Power Feeder on Jointer (w/pics)

#5

Lee Grindinger

Compromised jointer

Lee Grindinger

>A jointer's first role in the shop is to straighten edges and flatten faces. Your set up will certainly smooth lumber and it will do it very safely but the wood will not be straightened. The problem is that the feeder will press the bows out of lumber and these bows will not be removed. It's the old garbage in, garbage out routine that makes surfaced lumber from the yards such a PIA.

To remove a belly from a board it needs to be started on the outfeed table cutting nothing from the ends of the board until the belly is gone. Your feeder will start the cut right on the end and the belly will still be there. If you're running the board belly up you need to hit just the ends of the board until the whole face is flat. Pressure over the cutterhead from the feeder will press the bow out and you'll end up with the same problem but with less thickness to play with.

Think of a jointer as a powered hand plane and to use one properly takes the same understanding and finesse as a hand plane does. Your feeder is as dumb as a rock and does not know when to let the board's imperfections dictate how it passes over the cutter.

Surfaced lumber is a huge PIA for this very reason, it's never flattened first even though attempts have been made to devise a surfacer that flattens wood. Some can reduce bows but the indexing face is just too short to adequately flatten a board over a few feet long.

Your set up is not going to flatten lumber, it will only smooth it. Bowed lumber going in will be bowed lumber coming out. Frankly, your planer may be as good at this task as your power fed jointer.

If you need to ever produce a truly flat piece of lumber you'll have to do it by hand (using the jointer) because the nuances of the process are only available to the hand and eye.

Lee

Re: Mounted Power Feeder on Jointer (w/pics)

#6

Re: Compromised jointer

Scott Banbury

>Using a power feeder on the outfeed table as David has it set up will work fine as long as the depth of cut is set to take the entire width of the face in one cut. On twisted boards this will require careful balancing as the front edge is fed. Power might become an issue if cuts are deep.

For facing roughed out cabinet stack, it will be dream.

Re: Mounted Power Feeder on Jointer (w/pics)

#7

If you really stop and think about it I believe

henthorn

>you will come to realize that Lee is still correct. The bow will still be there since in order to get the wood registered on the out feed table the bow will already be compressed and the same amount of wood will be taken from the complete piece. Ergo, if the same amount is taken from the whole board the bow must still be there. The only way to remove the bow is take more off the ends until one side is straight and then thickness it with the planer. Any other way, it ain't going to happen.

Re: Mounted Power Feeder on Jointer (w/pics)

#8

Why it works....

David Eisan

>If this was a standard wheeled power feeder with solid highly sprung wheels, you would be correct.

However, this is a specialized feeder made specifically for a jointer. If you look at the last photo, you can see that it grips the board by grabbing it with the points of the wheels, not pressure. Each wheel is lightly sprung individually and rides up and down with variations of the board, it does not press down evenly over its width.

I too was a bit skeptical, but after using it on a couple of boards, I can attest to the fact that it does not simply smooth a face, but it flattens it as well.

David.

Re: Mounted Power Feeder on Jointer (w/pics)

#9

Why it works...

David Eisan

>Here is a quote from the manual,

"Recommended Feeding Pressure - Indirect and self-adjusting segmented spike rollers provide multiple contact points (segmented) with a sure-grip (spike). A light and sufficient pressure (to pull) is only needed to ensure a smooth operation without altering (bending) the physical shape of your stock"

The best way to describe it is that it does not rely on pressure to "push" the board through, but grip (spikes) to "pull" the board through.

Does that make sense?

David

Re: Mounted Power Feeder on Jointer (w/pics)

#10

I don't need to think about it, I just do it

Scott Banbury

>

Re: Mounted Power Feeder on Jointer (w/pics)

#11

Jason Roehl in Lafayette, IN

Makes sense to me!

Jason Roehl in Lafayette, IN

>Looks like a neat, ingenious little "toy". I'm one of those guys who likes the romantic notion of using hand tools in a patient process to shape wood, but doesn't have the time (or the tools) for that type of operation at this point in my life, so I go for power tools. When it comes to major sizing/smoothing operations, I like power tools that, once properly set up and adjusted take operator error out of the repetitive usage.

Jason

Re: Mounted Power Feeder on Jointer (w/pics)

#12

Re: Mounted Power Feeder on Jointer (w/pics)

Jim Shaver Oakville, Ontario

>Really well done David!

I like what you have done here, I find a lot of common sense in your approach.

Good to see you a few weeks ago as well.

Take care,

Jim