Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

help!!!!!please?

Posts

help!!!!!please?

#1

help!!!!!please?

tom chapman

>--------------------------------------------------------------------------------

I Have A Glued Table Top Pannel . It Is Basicaly 4' X 8' . It Was Flat In The Shop . I Bring It In The House And It Is Cupped About 3/16 In The Middle - Outside Edges Rolling Up . I Have Not Put Cleats On Or Fastened It To Aprons Yet. Nor Have I Put Any Finish On It. Should I Wet One Side Then Fasten It Down And Finish It Or What. The Wood Is Hickory .

Many Thanks

Tom

Re: help!!!!!please?

#2

Re: help!!!!!please?

Ron Hildreth

>Tom,

Leave it be to acclimate to the room temp, and it will probably return to flat. If it doesn't, then decide what to do.

Ron in Iowa

Re: help!!!!!please?

#3

Re: help!!!!!please?

Kneale Brownson awaiting snow in N. MI

>While you're letting it readjust, be sure air can get to both sides.

Re: help!!!!!please?

#4

Re: help!!!!!please?

Keith Newton------WebKitFormBoundaryDZmgloT+ZiYFgX

>Tom, I never recommend wetting, but I do recommend trying to dry the convex side more than the concave side when trying to control bowing and cupping.

If you have a radiant heat source that you can expose to that side will help it dry faster than the other, should help pull it back.

Re: help!!!!!please?

#5

Ellis Walentine

Table tops

Ellis Walentine

>Tom, it's hard to predict what will happen to this top unless we have a better idea of the moisture content and the cut of the wood (flatsawn, quartered, etc.). It would also help to know if the relative humidity in your shop is a lot different from your house. Regardless, I would not rely on a top this large staying flat on its own without aprons or cleats. My advice is to just let it acclimate for a while in your house while you make the base for it. Make the aprons wide enough to resist any cupping forces (but not so wide that knees can't fit beneath them). When you anchor the top to the base, use a sturdy attachment method, such as hardwood buttons, that will be strong enough to keep the top flat.

Ultimately, you want to finish both sides equally, so that seasonal humidity swings don't cause it to shrink unevenly on the top and bottom, causing more cupping and bowing.

Ellis Walentine, Host

Re: help!!!!!please?

#6

Lee Grindinger

3/16" in four feet?

Lee Grindinger

>Forget about it. 3/16" across four feet is nothing to worry about assuming the top is not 2" thick. I'd suggest you just finish it, evenly on both sides, and fasten it to your base which will hold it flat.

Lee

Re: help!!!!!please?

#7

Re: 3/16" in four feet?

Geary from NJ

>Reminds me of a disaster ,I caused from inexperience,but smile every time I look at it. I had a cherry slab,24" x 72" x 4"thick , cut out of center heart wood,for my rec room bar. I poured liquid plastic over 3 sides trying to accentuate the saw kerfs, and let it dry for 48hrs. Mounted it to the bar with 2" lag bolts. About 3 weeks later, I was asleep,in my favorie eazy,when all of a sudden,I thought someone crashed into the side of the HOUSE! But,in reality, the warpping 4" countertop slab ripped the bar out of the subfloor , the whole lenth of the bar. Moral of the story.....always finish all surfaces;at the very least....seal all sides. I have to admit,though, after loosening the top, all the way around it is kinda clever to see everyones' drinks self-centering themselves,in the middle of the bar. CHARACTER! Geary