Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Kinda embarassing question... Router bits

Posts

Kinda embarassing question... Router bits

#1

Kinda embarassing question... Router bits

Denis Ch�nard, Orl�ans, Ont.

>I have a few routers, some of which are of the cheap store brand type, or similar lot. I also have a few good ones, and the plan is for most of them (the cheap ones especially) to attach a Rousseau or import equivalent plate, set them up with a specific router bit, and use them specifically for one function. When need arises for one bit, just pop the router in the table, and I'm all set to go.

Now the question is, what bit(s) would you set up permanently in a router, given frequency of use? I can think of a flush trim bit, maybe 1/4" quarter round, what else?

I have six routers, nothing like Norm :-)

TIA,

DC

Re: Kinda embarassing question... Router bits

#2

Tell me what routers you have, & I will give you..

Art Silva

>the solution to your problem. Art

Re: Kinda embarassing question... Router bits

#3

Re: Kinda embarrassing question... Router bits

David Yoho

>If I were to do what you are planning, I know which six I would set up. However, those I use with more frequency may not necessarily be the same as you. I think you need to determine which bits you use the most and set those up.

I like the sound of the idea and think it could be a nice time saver - kind of like having a second tablesaw and setting it up with a dado blade. Let us know how it works out!

David

Re: Kinda embarassing question... Router bits

#4

Re: Kinda embarrassing question... Router bits

Barry Irby

>What do these router plates cost and where do you get them?

If I were doing this I would go with a heavy duty edge trimming or pattern bit and a round over. I'm with you on that. Next I would have a straight cutting bit, perhaps a carbide spiral bit, about a half inch or maybe 3/8". I have found numerous uses for such a bit. And I would have a dovetail bit. I have cut a number of sliding dovetails recently. I would coordinate the two bits so that I could use the straight bit to hog out most of the material and then cut the DT part with the DT bit.

I don't get as much use out of my router(s) as I should. This might be a good idea. OTOH I jump around from flat work to turning, little stuff to big stuff, furniture to decks, etc. You need to mentally log which bits you use most for what you do, or you could just start using them and see which ones get left in the router until they wear out. (I have a DT jig and two routers dedicated to it, the bits stay in and set up, I should make more drawers.)

Re: Kinda embarassing question... Router bits

#5

Re: Kinda embarassing question... Router bits

Greg Haugen

>For most a tablesaw is the "heart" of the shop. For me it's my routers. The bits I use are different from the next person's bits. IF you make a "comon" item or style of project here is what I'd do. Walk yourself through the project and lay out the bits you would use. You'll start to see a pattern. You've got six routers, if you end up with 7 or 8 bits group a few of the extras either by the sequence used or collet sizes. If collet sizes become an issue, collet adaptors are priceless for fast bit change with different collets. It's tough for someone else to set-up tools for another. They may like 1/4 rounds but you may use a different size or an ogee or something else. By looking at this way, you may be able to get a better feel for what you need.

Hope it helps,

Greg

Re: Kinda embarassing question... Router bits

#6

Re: Kinda embarassing question... Router bits

knotscott

>I'd guess everyone's mileage will be different with this one. I'd have to say I use a 45 degree chamfer as much or more than any. I may use a roundover more often than a chamfer, but not the same size roundover every time.

Re: Kinda embarassing question... Router bits

#7

Re: Kinda embarassing question... Router bits

Jim Dillon

>Denis,

Like Knotscott, I probably use the roundover bit the most in my table router for moldings etc. But the problem is that I use a different radius roundover depending on the situation and some have a 1/4 inch shank and some 1/2 inch. I often keep a 1/8 inch roundover (1/4 inch shank) in my PC-310 laminate trimmer full time as it is just so handy to reach for it while working on something. I'm not sure there is a good answer to your question especially if you are doing a variety of things. Wish I could be more helpful.

Jim

Re: Kinda embarassing question... Router bits

#8

Re: Kinda embarassing question... Router bits

George@Colonel's Workshop-Havertown PA

>Hello Denis,

Geeze, I feel somewhat inadequate because I only have 5 routers including the laminate trimmer. The only bits I'd want to keep permanently set up are the panel raisers and accompanying cope and stick profiles. I have several of these sets, and buying big routers to accommodate them all is impractical. My laminate trimmer is mostly used to gain small cabinet hinges and I always have it loaded with a two flute 1/4" straight bit. I am hoping my new Jessem Mast-R-Lift solves the set up problems with the others. Its cheaper than buying more routers.

George

Re: Kinda embarassing question... Router bits

#9

I leave two router bits set up

Lee Schierer - McKean, PA

>I leave two router bits set up. One is the last bit I used in my router table

The only other bit I tend to leave in my router is the dovetail bit that I use for my dovetail jig. Leaving it setup saves time when I need to make drawers so I don't have to adjust to get eh perfect height to get proper fit in the dovetails I cut.

Lee

Re: Kinda embarassing question... Router bits

#10

Re: I leave two router bits set up

Michael Wangler in Rochester, NY

>I agree with Lee.

Tweeking out a router/ table to cut dovetails takes way too much time to set up. If I had just one more router that is what I would dedicate it to. I currently have one in a table, one to use free hand and a small trim router.

Michael