Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Rubbing out finish question?

Posts

Rubbing out finish question?

#1

Rubbing out finish question?

Barry Irby

>I made little doll cradles of walnut and finished them with Deft Gloss Lacquer from spray cans. Pretty happy with the results, but would like to rub the finish a bit to knock the little nits off the surface. Don't really want to kill the gloss. I have used OOOO steel wool, but it tends to cut the gloss a bit. What do you use to do this?

Re: Rubbing out finish question?

#2

Re: Rubbing out finish question?

George@Colonel's Workshop-Havertown PA

>Good Morning Barry,

I use 4/0 steel wool also. Dip it in a shallow dish of naptha and lemon oil and rub lightly. Wipe again with pure naptha and then with a dry clean cloth. The shine will be reduced to a satin/semi-gloss, but you will be left with a smooth surface. You can apply some paste wax and buff.

George

Re: Rubbing out finish question?

#3

Re: Rubbing out finish question?

Garrett in Victoria

>I just did the same on a small project as the Colonel recommends, i.e. 3/0 then 4/0 steel wool but with varsol as lubricant. Followed up with Behlen's Rottenstone and water, and finished with Minwax paste wax buffed. Smooth as... well... a baby's bottom, and shiny.

Cheers, Garrett

Re: Rubbing out finish question?

#4

Re: Rubbing out finish question?

Dave Bair, Eaton Rapids, MI

>If you are simply removing dust nubs, burnish the wood with pieces of a brown paper sack or other coarse paper. Just be sure there is no embedded grit; the paper itself will not scratch a fully-dried finish.

Re: Rubbing out finish question?

#5

Re: Rubbing out finish question?

Ron Jackson

>I most often apply paste wax with 0000 steel wool.Not a super high gloss but I like the slightly knocked down look.

Re: Rubbing out finish question?

#6

Re: Rubbing out finish question?

Ken Oakley-Sunny St. Cloud, Fla.

>Colgates tooth paste works as a polishing agent also. I guess any other tooth paste will work also. I prefer a product called Simi-Chrome which is used as a high end metal polish. Works for me.

Re: Rubbing out finish question?

#7

Automotive rubbing and polishing compound

Michael Dresdner

>

Re: Rubbing out finish question?

#8

If you are talking about very small imperfections

Chris Knob

>and you want to retain high gloss, even 0000 steel wool will scratch the surface enough to satinize the gloss. No matter how much wax polishing you do after that treatment, you will never get more than a semi-gloss finish. The scratches from the wool will need to be supplanted by scratches from finer abrasves like 1000 and 2000 grit wet dry paper or automotive polishing compounds. Sometimes, just a hard buffing from a terry cloth towel is enough to knock off the surface imperfections without scratching the hard gloss surface too much.

Re: Rubbing out finish question?

#9

Thanks All

Barry Irby

>I have heard it said that building something is half the work and finishing it is the other half. That may be true. I like and enjoy the building half and can just barely tolerate the finishing half. (What I should do is find somebody that likes the finishing half and build two, and give them one for finishing mine.)

I think I am going to try the suggestions in order of ease. I will do the easy ones first and see if they work. If not, I will go to the others. Thanks again.

Re: Rubbing out finish question?

#10

Re: Thanks All

Dan Donaldson

>Designing it is the first half, building it is the other half and finishing it is the other two-thirds ;-)

Re: Rubbing out finish question?

#11

Re: Thanks All

Barry Irby

>I harvested the trees myself. That was at least half the work. Then there was the building of the shop and working my real job to buy the tools. That was about half. And you are right, designing is certainly an important half. Building the piece is the fun half and finishing it is just the necessary last two thirds.