Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Choosing a HVLP Conversion Gun

Posts

Choosing a HVLP Conversion Gun

#1

Choosing a HVLP Conversion Gun

Jerry Draper

>I want to purchase a HVLP conversion spray gun. The gun most frequently mentioned in the archives is a Wagner from Gleempaint.com. Does anyone currently use this gun and would you buy it again? Any other recommendations? I will be spraying latex, enamels and varnish. I have a 2hp 5 gal. compressor that I have used successfully with conventional spray equipment. Would appreciate some guidance.

Re: Choosing a HVLP Conversion Gun

#2

Re: Choosing a HVLP Conversion Gun

frank shic

>i bought the gun and it does an alright job with clear finishes as long as you have a decent size air compressor (my porter cable pancake could NOT keep up while spraying water-based conversion varnish on kitchen cabinets) but it works terribly on latex unless you thin it down a great deal. you may want to look into an airless sprayer for latex as it's pretty thick stuff.

Re: Choosing a HVLP Conversion Gun

#3

Re: Choosing a HVLP Conversion Gun

mdclor

>Check out Jeff Jewitt's site homesteadfinishing.com. I hope this isn't a violation of protocol.

Good luck,

Merle

Re: Choosing a HVLP Conversion Gun

#4

DeVilbiss or Sata

Clint Searl, at the base of Haycock Mtn

>

Re: Choosing a HVLP Conversion Gun

#5

Re: Choosing a HVLP Conversion Gun

Gary Ratajczak

>I have the Gleem gun - used it about 3 years. I spray only latex through it for primitive furniture. My formula is as follows:

- Gleem offers plastic pots with covers - they are great, and let you store pre-mixed

- I thin with about 3/4 paper cup full of Flotrol (avail at hardware and big box)

- I add about 1/2 cup of water

- Remainder is semigloss acrylis latex

- Tip - Be sure to take the needle out every once in a while to fully clean.

- Gleem offers needle kits in addition to what is offered standard in the gun - they are GREAT to work with - give them a call, and tell him what you want to shoot

I don;t spray a ton of material, so this gun was the right proce for me - i would buy again!

GR

Re: Choosing a HVLP Conversion Gun

#6

Re: Choosing a HVLP Conversion Gun *LINK*

Mark Mandell - Gone Round In Jersey

>Jerry,

I would anticipate that you'll be choosing a new compressor as well. That small unit is going to put out 4 "real" CFM if you're lucky and that won't qualify for a "high volume" gun. You may be able to spray some finishes with it, but I doubt it will have the ability to atomize latex, even with Flotrol added, to the point of providing an acceptable finish. Moreover, most any gun you buy will use more air than your current compressor will put out. That means that you'll have to stop often and allow the unit to catch up, and the small storage tank will tend to transmit the compressor pulses to the gun which will result in uneven spray. The suggestion to put your question up on Jeff Jewitt's site's finishing forum is a good one; see the link, and click on the forum tab. You can also contact Jeff directly. You haven't said what your budget is. Jeff sells a variety of guns that range from $150 up through $600.

Although you have asked about "conversion" guns (that work off of a compressor), you should also consider one of the turbine outfits. A good turbine gun outfit is not going to be cheap, but it is likely to be less that buying a descent conversion gun plus a new compressor with enough guts to run it.

mm


Homestead

Re: Choosing a HVLP Conversion Gun

#7

Re: Choosing a HVLP Conversion Gun

Jay St. Peter - Southern, MD

>I talked to jeff and bought a gun from him myself. He will be able to recommend a gun for you since your compressor and desired finishes are different than mine. If I was to do it again, I'd look more seriously at Sata equipment also (I've since met a bunch of car paint guys and they've preached to me ;)). But, no regrets for the wood finishing. All the WB stuff I've sprayed has turned out great.

I bought a gravity feed HVLP gun. For the majority of stuff it works great. But, I sometimes wish I had a pressure pot gun when things get tight. I can usually figure out a way to prop the piece to get an angle on it, but it would be easier if that wasn't necessary.

Jay

Re: Choosing a HVLP Conversion Gun

#8

He Who Dies . . . . .

Mark Mandell - Gone Round In Jersey

>I run a Walcom with a 2qt. CA Bandit pressure pot and it does an amazing job. But . . .

It's too much rig for finishing a bowl, a small piece, or a touch up repair. Thus I have a grav-feed small gun on my Christmas list.

Seems like whatever you buy, there's always something more to buy. |;-}}}}

mm

Re: Choosing a HVLP Conversion Gun

#9

Thanks to all. Very helpful info.

Jerry Draper

>

Re: Choosing a HVLP Conversion Gun

#10

Re: Choosing a HVLP Conversion Gun

Jim Dillon

>Jerry,

I have the Wagner HVLP conversion gun from Gleem Paint. So far, I have only used it to spray latex. I use it with my 1-3/4 HP hotdog compressor. For the money, I am very pleased with the gun and results. I use the #4 tip (intended for latex) and follow Gleem's guidance for pressure at the tank and gun. Initially, I diluted with Flotrol, but this past summer I sprayed quality latex undiluted and it worked just fine. I was impressed with the fittings and polish on the gun, but then again, I have nothing to compare it to. I didn't want to spend a lot of money on something that I only use once in a while. Yes, the compressor runs a lot and this would be a drawback for a large project and moisture sensitive finishes unless you had a moisture trap. I plan to get a permanent and disposable water trap later on. If you want to invest more, do indeed check out Homestead Finishing for some quality spray guns and accesories. Hope this helps.

Jim

Re: Choosing a HVLP Conversion Gun

#11

Re: Choosing a HVLP Conversion Gun

Jim

>Jerry, a couple of these posts mention the Wagner gun from Gleem. I bought one but before using it picked up an hvlp turbine set up. If you're interested (never used in the box) drop me an email.

Re: Choosing a HVLP Conversion Gun

#12

Jeff Jewwett is an extraordinary resource

Howard In Toronto

>But if you want to test the waters very very cost effectively, one of the not-so-best-kept-secrets is P-C's HVLP gun.

Here's why -

- well-made = zero leaks

- tons of spares/replacement parts = you can use it forever

- variety of needle/nozzle sets = lets you spray ANYTHING

- wide distribution = big competition = good deals

- evergreen product = P-C ain't getting rid of it for a long while

- not the biggest HVLP airhog = more flex with different compressors

Check it out - it consistently gets great reviews.

I've never used one of the gold standard guns like SATA and DeVilbiss but my P-C HVLP gun sure does everything I could think of.

HTH

Howard