Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Need help with a really bad staining job.!!

Posts

Need help with a really bad staining job.!!

#1

Need help with a really bad staining job.!!

lee beeden

>Why I decided to stain this project in the first place I don't know, I should have just put a hand rubbed oil finish on.

the wood is Birch.

Its a medicine cabinet

First I brushed a 2ib cut of white shellac on to seal it, looked pretty good afterwards.

secondly I wiped on a coat of black walnut gel stain.

it looked terrible so I let it dry 8hrs and put on another, looks even worse.

there must be a way to save this cabinets, I'm pretty proud of it, but not now!!!! Arghhhhhhhhhhh!!!!

I did do a tester, honest!!!!!!! Not sure what went wrong

Any help very much appreciated!!!!

Lee

Re: Need help with a really bad staining job.!!

#2

Ellis Walentine

Hmm. A possibility for you...

Ellis Walentine

>I don't usually apply stain over a sealer, so this is somewhat speculative. By sealing the wood with a 2# cut of shellac, you're keeping the stain from reaching the wood. Instead, you are trying to put a superficial coat of stain on top of the sealer coat itself. The solution I'd try is to strip the medicine cabinet back to bare wood or some semblance thereof, as you will not get all the shellac off at this point. I'd wash it down with naphtha first to remove residual pigment from the stain, then I'd go after the shellac coat with denatured alcohol and some Scotch Brite pads. Use plenty of alcohol and dry rags to remove as much shellac as possible. This will probably have the effect of spreading out whatever is left of the stain and amalgamating it with any residual shellac. At this point, if you still want that dark color, you should be able to wipe it on successfully.

Again, without seeing the piece or really knowing what you've already done, this is speculative, but probably worth a try. To be safe, either comp up an exact sample of the offending wood and finish, or try my suggestion on an inconspicuous part of the piece.

Ellis Walentine, Host

Re: Need help with a really bad staining job.!!

#3

Re: Hmm. A possibility for you...

Brian Green

>First, a couple of assumptions. 2lb white shellac is a light clear as opposed to amber or seedlac and not the white pigmented variety and the gel stain is the color your shooting for. Often times the washcoat of shellac is used to prevent blochyness, esp. in cherry, maple and of course birch..so is using a gel stain.

I've never seen a 2lb cut used for a washcoat to prevent blotching, often times finishers use a 1lb cut or even 1/2 of that, similar technique as using glue size on endgrain. After that you lightly sand to allow the top fibers to soak up the stain. You've sealed the wood and the gel stain really doesn't penetrate well to begin with. As Ellis said, I'd use a solvent to wipe off the gel stain (stain directions will tell you what you need for clean up), it should redesolve and take most of the gel stain off. Now you have a couple of options:

1. Probably the easiesy is to make a toner with trans tints and shellac, or possibly use your gel stain in shellac (if it will dissolve). This will allow you to add uniform color in layers, don't try and get it in one coat (your toner is too strong). Not sure how your putting on the finish (french polish vs spraying vs brush) so this may take 4-5 coats. Then top coat with the clear shellac or finish of choice.

2. Sand back to bare wood and start again....yuk

of course as you already said a small sample board would have shown you if this is what you wanted...trying to do a finish on a project without this step well, been there, done that, have the tee-shirt.

Good luck, I'm sure that you can salvage your project, it'll just take alittle longer.

BG