Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Perils of Home Depot plywood

Posts

Perils of Home Depot plywood

#1

Perils of Home Depot plywood

Bill Tindall, E.TN

>I bought some Home Depot birch plywood. It had many plies so I thought it should be stable like Baltic Birch.....Wrong! First thing I observed was warping in the shop. Checked moisture at 18% . Not good for cabinet work. So I mashed it among many sheets of other plywood to let it dry out for a year. Started to used some recently. I have never seen plywood so humped up. The picture of a sawed edge will show why. Can you believe it! It was thrown together and mashed flat... more or less. The face ply was measured at 0.011" thickness. Not much room to sand it any flatter.

I brought these quality issues to the attention of Home Depot management. Their response was one of unconcern. If they are unconcerned it follows that they will continue to stock this material. Hence, the perils of buying plywood at Home Depot.


img

Re: Perils of Home Depot plywood

#2

Not Just Home Depot

Mike Fitterling

>I was doing a huge kitchen job last year and this and used a ton of walnut and maple ply from a wholesale supplier. I had several sheets of $100 a sheet walnut ply separate almost its full width and length. I just now am making some bookcases out of maple ply (A1) and missed a defect until after assembly. They had over lapped plys and left a very noticeable ridge across the sheet. I am now going to have to apply a new veneer over that sheet (after sanding it flat) to fix and finish the job. I have seen plys like your picture on pretty expensive sheets of plywood. Where's the quality control, even on these high end and high cost products? At least with this supplier I get credit for bad sheets, but they happen too often and hold up production until new stuff arrives, and I just hate doing things over. Grrrr. Note to self: look over very very carefully every sheet before cutting for component parts.

Re: Perils of Home Depot plywood

#3

Re: Perils of Home Depot plywood

Dick Coers

>I know that the Home Depot plywood is from China, don't know about the stuff from your wholesalers. It is absolutely s**t. Not only are the plys smashed like that, but the glue just barely holds. Then there are the excessive levels of formaldehyde used in the glue as well. (Maybe the glue supplier is the same place providing all that "good" paint for the toys)I hauled a couple of sheets around in my van this summer for a few days. On a really hot day my eyes started to burn when I got in the van. It was really bad. Today I read that MDF showing up in bad batches as well. The guy was saying that the surface of the MDF was coming off with the contact cement and laminate. It seems they are putting less adhesive in the mix to save money.

I fear this is only the beginning. It probably won't be long before all the mills will be shut down in North America because the housing market failure. Then these crap mills in China will be the only place to buy. Their plan works again.

Re: Perils of Home Depot plywood

#4

Re: Perils of Home Depot plywood

Alan in Little Washington (NC)

>Ah, yes Grasshopper. The ox is slow but the earth is patient!

Re: Perils of Home Depot plywood

#5

Re: Perils of Home Depot plywood

Ken Krawford

>That looks exactly like the stuff I just picked up from them. It had a sign on the stack saying "Cabinet grade plywood". Ha-ha.

Re: Perils of Home Depot plywood

#6

It comes from China, and is a bargain that isn't

Garrett in Victoria

>I made the mistake of buying a dozen 3/4" sheets of this stuff in 'mahogany' veneer about 18 months ago for a basement storage project. Those I fastened to stout framing have been fine. Those I used for unframed doors have bowed, as have a few full sheets left over.

Another bargain that wasn't.

Cheers, Garrett

Re: Perils of Home Depot plywood

#7

Silly guys....

Eddie Pacheco, San Jose, Ca.

>That ain't plywood. That's what the big box stores use as dessicant! It soaks up the moisture from the 2 by lumber that they have on hand.

Re: Perils of Home Depot plywood

#8

Re: Perils of Home Depot plywood

albertabob

>I don't buy anything from Home Depot unless it is the last resort.

Please don't misunderstand me, I have no vendetta against the company.

In fact I don't really know who they are?

It's just that I am older and my experience is different.

I have become accustomed to 'hardware men" who knew their product and were happy to help me with my current problem.

Not to be confused with wholesalers that dealt only with the trades.

Today,what I see, is a 56 year old drop out holding a "high school after class job" and doing a rather poor job of it too!

I see management that looks the other way thinking I have paid all that the product it worth and should not ask for any better.

I feel betrayed because I was never asked about how poorly made the product I have had to choose was made.

As a matter of fact, I AM BEING DRIVEN to the bottom by the will of a corporation that cares not a wit about my well being nor the well being of the country.

That is just plain wrong!

Bob

Re: Perils of Home Depot plywood

#9

Jesper, Denmark

Geeee.... I'm so glad we get our stuff ....

Jesper, Denmark

>...from Russia, Sweden and Finland. And a little bit from Canada too when it has to be real cheap.

Re: Perils of Home Depot plywood

#10

The other box stores are the same...

Kris Lasure

>Our Lowes in south central Indiana used to carry Columbia Forest Products oak and birch ply. Good stuff. Now they have started handling that Chinese crap that doesn't even sit flat in the store. Menards has the same stuff. Multi layer ply that looks like it might fall apart if you look at it the wrong way!

Luckily last year I bought several sheets of the Columbia plywood and have a 1/2 dozen left. What gets me too is that I paid 29.50 a sheet for 3/4" birch and now this import stuff is 38.00 per sheet.

Go figure.

kl

Re: Perils of Home Depot plywood

#11

Re: Perils of Home Depot plywood

Gary Camp, Bend Oregon

>Went to Lowes the other night, I needed washing machine hoses at 8pm. I walked past the lumber (using the term loosely) aisle and just had to shake my head. I must be really hard to get sheet good to lie flat if you can't even get the shelving arms in the same plane to start with. Maybe they were trying to reverse some pre-bent sheets and allowing for springback.

glc

Re: Perils of Home Depot plywood

#12

Re: Perils of Home Depot plywood

Gary Camp, Bend Oregon

>Went to Lowes the other night, I needed washing machine hoses at 8pm. I walked past the lumber (using the term loosely) aisle and just had to shake my head. I must be really hard to get sheet good to lie flat if you can't even get the shelving arms in the same plane to start with. Maybe they were trying to reverse some pre-bent sheets and allowing for springback.

glc