Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Quality Router Bits

Posts

Quality Router Bits

#1

Quality Router Bits

Ray DuBose - Memphis TN

>Haven't done much with my router in the past but starting to get more into it. Have a router Plate on order and have made a few accessories for it lately.

Now I'm finding myself wanting to invest in good router bits and trying to figure out who the top performers are. I've picked up a few Bosch ones that I don't care for and from some of the reviews I've read aren't very good.

I keep going back and looking at Whiteside but can't find many reviews on them. From what I gather Freud are pretty solid performers. Don't know much about CMT either. I don't mind dropping a little more on a router bit that will leave a cleaner edge and last longer.

Suggestions?

Ray

Re: Quality Router Bits

#2

Re: Quality Router Bits

Ken Oakley-Sunny St. Cloud, Fla.

>CMT is a quality product. Whiteside is another good one. They make cutters for Eagle Amaerica, who I purchase from. They also supplied Woodcraft a number of years back. I purchased some there also. I have been happy with the Freud cutters I have used.

Re: Quality Router Bits

#3

Re: Quality Router Bits

Robin Corell, in Atascadero CA

>I have had great results with whiteside and Amana. I have been very disapointed with CMT and I think freud has a lot of adds that they have to pay for somehow.

Robin

Re: Quality Router Bits

#4

Re: Quality Router Bits

Lee Schierer - McKean, PA

>I've been very happy with my Freud router bits, all perform very well. I would not recommend Viper, Woodtek or Craftsman bits based on my experience.

Lee

Re: Quality Router Bits

#5

Re: Quality Router Bits

George@Colonel's Workshop-Havertown PA

>Good Afternoon Ray,

I have had very, very good results from Freud, Amana, CMT, Jesada, and Woodline. I have not used Whiteside bits per se. I have also bought a few from LCMS/Penn State Industries and Eagle America to satisfy an immediate need/limited use. All bits have worked for me, and I do use the router a moderate amount: several times weekly. I do not hesitate buying a less expensive bit when I expect its use will be limited, like a key hole bit. It pays to get good tooling for popular coves, beads, and straight profiles.

George

Re: Quality Router Bits

#6

Re: Quality Router Bits

Larry Clinton

>I have finally settled on Whiteside - I have a cabinet set by Freud which works well, but I have one pilot bit that I didn't care for. I also have some Leigh, CMT, Lee Valley, Rockler, Craftsman and Woodtek. IMHO, the Whiteside bits preform as well as or in most cases better than any other bit I've tried. They are made in the USA, priced with or just a little lower than CMT. I recently bought a full set (except one bit they don't make) for the Leigh jig, and have a set of the corner radius bits, and Ogee bits. From now on I buy only Whiteside. By the way "Routerbits.com" is a sponsor of WoodCentral, and has the best prices I've found on Whiteside. I always try to buy everything i purchase from WC sponsor's if they carry the items.

Re: Quality Router Bits

#7

Pins then Tail no Tails then Pins

Dustmaker Mike

>wow what a question. Kind of like asking if you cut the pins or tails first on Dovetails.

I have a wide selection of router bits. They have all done just fine for me. I use them on a now and then basis so my milage will very from yours. Fraud, CMT, Infinaty, and some Craftsman. I keep them clean and in a nice box so the carbid tips won't hit each other and chip. I think the handleing and cleaning of them has to do a lot with how they work for you. There a few thousdand folks that visit here and we all have opions on what to use. I even tried a Harbor Frieght bit because I thought there where bits of nails left in the board I was going to route and it seemed to do just fine.

Run them fast run them clean take small last cuts and they all do a good jobs. Just my opion

Re: Quality Router Bits

#8

Re: Quality Router Bits

Thomas S Stockton

>Pretty much all I buy are amana or whitesides good qaulity. I have some cheaper bits that I bought to use for one job, they work fine they just don't seem to hold an edge as well.

Go to the marketplace section and click on routerbits.com they carry whitesides bits.

Tom

Re: Quality Router Bits

#9

Re: Quality Router Bits

Patrick Schupbach

>I have had good results with Infinity Bits& Blades.Whiteside & Amana are both quite good.

Re: Quality Router Bits

#10

Re: Pins then Tail no Tails then Pins

Ray DuBose - Memphis TN

>Yea I know it's opening a can of worms. I just have no investment in router bits and want the best bang for my buck.

Thanks for your reply

Ray

Re: Quality Router Bits

#11

Re: Quality Router Bits

Gordon Sampson

>Ray,

I have quite a few CMT router bits and really like them. Also have a few Jesada bits. Whiteside makes quality bits also. I guess it all depends how much you want to spend and if you want a throw-away bit vs. a bit that you'll sharpen a few times. The Whiteside bits are well made and a little less expensive than the CMT bits.

I do recommend not buying "packages" that have a number of different bits included in the package. Determine what you need the bits for and buy accordingly. Packages sometimes have bits you'll never use. Just my opinion.

Gordon

Re: Quality Router Bits

#12

Go with Eagle!!

Tom Norton

>Since I live in the saem town as eagle America!! Great for me when I need to run out and get a bit!

Re: Quality Router Bits

#13

What he said

Tony - Memphis

>Howdy neighbor!

I've only had one real issue and that was with an MSC bit. It was a flaw on the top of a crown bit. They took care of it. I have some old Sears bits I have been using for ten+ years. I use Eagle, Lee Valley, Amana, etc. I've never been able to tell any difference. I really like the CMT bits, but its just a subjective thing. I have bought some from that place in Bartlett in a pinch (their prices are pretty high). I've also bought some from HD and Lowes (whatever their brand of the day was) and they seem to work fine. For reference, I am a weekend warrior type building furniture. I use mostly mahogany, cherry, and maple.

Tony

Re: Quality Router Bits

#14

Re: Quality Router Bits *LINK*

David Yoho

>Ray, there are any number of quality router bits on the market. Looks like there's a lot of folks satisfied with Whiteside bits here. I think I have one of their bits and don't have any complaints about it but don't have enough experience beyond that one bit to say more than that.

For me, the key to your question is what is the best bang for your buck. So far, in my experience in my shop, I've been buying and using the Infinity bits long enough now that I can say they are the best bang for my bucks. They are good quality at very reasonable prices. Check for yourself at the link below.

David


Infinity Tools

Re: Quality Router Bits

#15

Re: Pins then Tail no Tails then Pins

GaryMc

>And free shipping from Eagle this week, thru 11/26. Coupon code EAGL071120.

Re: Quality Router Bits

#16

Re: Quality Router Bits *LINK*

knotscott

>My best bits are Whiteside and Infinity. The Whiteside bits are top shelf, made in the US, and have a pretty good retail distribution. Holbren.com has good prices, good selection, and free s/h.

7 or 8 years ago, Finewoodworking did a router bit comparison and picked Whiteside as the best bit. This year they did another bit test and chose Whiteside again as best overall, plus best value.


img

Holbren