Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

OT changing the light bulb!

Posts

OT changing the light bulb!

#1

OT changing the light bulb!

Philip Duffy

>OK, lets get the jokes out of the way first; How many sailors does it take to change a light bulb at the top of a blind stairs? Just one, but it takes him 2 hours!

Got a reach pole with a sticky plastic attachment; not a chance to pull that bulb 8ft up the stairs. Tried CA glue next; no chance. Got a basket arrangement as well; no luck, but it sure got all the paint off the insides of the bucket where the bulb sits. How about an invention? Sure enough, a piece of 150 sandpaper and some hot glue to hold it in place on a turned base of wood, and some more hot glue to stick to the bulb, and Voila! A bulb is out! The new bulb is one of those energy savers with a squirrel cage look so I made an insert with two dowels on a piece of wood that holds the hold thing in place while you screw it in. It works. - -just don't pull the dowel piece out without considering the fragility of the energy-saver bulb. Be careful of the broken glass all over the stairs! And, don't forget to lube the threads on the new light bulb. Philip

Re: OT changing the light bulb!

#2

You MUST have been a GI ! . . .

Steve Mackay

>THATs some TACTICAL think'n !

Re: OT changing the light bulb!

#3

Re: OT changing the light bulb!

David G. Sparks

>I'm curious what you use to lube the threads on the new bulb? It sounds like a good idea. Thanks!

Re: OT changing the light bulb!

#4

Re: OT changing the light bulb!

Rod Peterson -- Ormond Beach

>> I'm curious what you use to lube the threads on the new bulb?

I'm not the OP, but what I've used on light bulbs (when I think of it) is Penetrox (marketed by Burndy, an electrical devices supplier—or NoAlOx, a similar, competing product), a conductive grease used primarily for electrical splices in aluminum conductors. Because some bulbs can get really cranky if they've been in a socket for a long time, particularly if the glass is especially fragile, and especially if it's an outdoor installation, it's a good solution.

I was first introduced to Penetrox when I came into possession of a Mosley antenna many years ago. They are constructed of aluminum tubing, each subassembly of which consists of telescoping sections. They actually supplied a small packet (a little goes a long way) of the stuff. Not only does it lubricate (not a big deal with fresh aluminum), but it retards corrosion making eventual disassembly or adjustment not only possible but easy. At one time, I was involved in quite a few antenna installations and I bought a bottle of it which I used on every antenna I ever put together.

I also used it recently in a house-wide window screen repair which involved lubing up rotating tabs used to keep the screens in place. Every single one had corroded to the point of being inoperable although they came apart easily with the removal of the pivot screw (which I also lubed on reassembly). Everything went back together with Penetrox applied. I doubt I'll ever have a problem again.

Nice stuff (but messy), and whatever size you buy will likely be a lifetime supply. It's applied sparingly—I'll bet I haven't used 1/8th of that 4oz. bottle I bought years ago and I've assembled a lot of antennas.

One caution—make absolutely sure you don't get any in the area between the threads and the center contact of the bulb—it's conductive grease. I usually leave the first thread uncoated just to be sure.

Rod

Re: OT changing the light bulb!

#5

Also not the original poster

Bill Houghton, overcast in Sebastopol, CA

>but I've done a light spritz of WD40 (which is non-conductive) on the base of light bulbs before installing for years. I just hit the button quicklike, then lightly wipe it around (not off) with a paper towel, trying to keep it on the threads, not past.

Seems too simple to work, but it do.

Re: OT changing the light bulb!

#6

After all, everyone has WD-40…

Rod Peterson -- Ormond Beach

>…it takes geeks or sparkies to have Penetrox in inventory.

Rod
who's a little of both.

Re: OT changing the light bulb!

#7

Re: OT changing the light bulb!

Bill Falberg

>I use any pole long enough (16' in one case) and wrap Duct tape around the end with about 4" of free tape just flapping loose. If you catch the end of the "flag" piece on the bulb you can wrap it around the bulb and turn it out with extreme leverage. CCW and CW end-wraps are determined by which way you're going; old one out - or new one in. When you put the new one in you'll want to rotate the stick to re-wrap the overhanging "flag". Careful not to orbit the bulb or you'll unscrew it. Simpler than it sounds probably but worked every time for me; never broke a bulb that way.

Re: OT changing the light bulb!

#8

Re: After all, everyone has WD-40�

Dan Donaldson

>The two staples in every home are WD-40 and duct tape. If it moves and should not, duct tape it and it it doesn't move and should, spray it with WD-40 ;-)

Re: OT changing the light bulb!

#9

Re: OT changing the light bulb!

John E in SC

>Small dab of Vaseline seems to work also - I'm not sure if it's conductive or not, but I just apply a little smear to the threads, and have never had a problem.

John