Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Planer problem

Posts

Planer problem

#1

Planer problem

matt ankney

>Tonite I was planing the cypress for my cabinet doors, it is not rough sawn already surfaced but to thick, and the grain was like peeling up as it came out of the planner! I have never seen this before, I just finished planing some oak and maple and it was fine so I dont think it is a planner problem, If anyone has any Idea what is going on please help!! Thanks Matt

Also my planner blades have not been sharpened in a while if that matters but the seem do be cutting fine.

Re: Planer problem

#2

Re: Planer problem

Thomas S Stockton

>Matt,

Probably caused by dull blades. Never worked with cypress but some woods are prone to the grain lifting and it is made worse by dull blades like redwood and flat grained fir.

T

Re: Planer problem

#3

Another point: cypress is

Forrest Addy

>Another point: cypress is tough on planer knives because of its silica content. Figure on sharpening your presently dull knives immediently. If you don't have a spare set now is the time to get a set. If you have several hundred feet of cypress to plane/join and the knives poop out again install the spare set and get back to work. Clean surfaces with unseparated grain is worth a little messing around with changing knives. Peeled grain can be a huge and ugly PITA.

Don't get overwhelmed my my gloomy prognostications. The silica content will vary quite a bit. Most "swamp woods" (as I call them) like cypress,cedar, many tropical woods, etc contain some silica and can be worked in the usual fashion so long as the cutting edgee are watched. Some swamp woods may contain a lot of silica depending on their growing environment. Your knives will wear accordingly.

As was said dull knives will cause the grain to lift.

Re: Planer problem

#4

Re: Another point: cypress is

matt ankney

>I know about silica as I do a lot of custom boat work using teak and man that stuff will dull blades fast. I just never seen anything like this before, the wood/grain actually peeled in layers, I tryed a few boards and all were the same so I am changing knives asap. Thanks for the info.. Matt

Re: Planer problem

#5

Re: Planer problem

David Yoho

>I don't think you are experiencing a planer problem. It sounds like the same thing I saw once before when working some cypress I bought. I think it's more to do with the nature of new growth cypress. If it looks like the grain is lifting or peeling from the surface where there is "cathedral" pattern in the grain, then I'd blame it on the wood. Don't know why this happens but I've seen it before.

David

Re: Planer problem

#6

Re: Planer problem

Bill White

>You could have some cypress with "wind shake". Actually is caused when the internal structure of the wood is not tight. I've seen some where you can peel a whole cathedral off the board very cleanly. Looks like the layers of the wood are not connected to each other.

Now this is my oversimplification, and I'm sure an arborist can give a much more technocal explanation.

Bill

Re: Planer problem

#7

not uncommon

Bill Tindall, E.TN

>I see this problem with some frequency in the occasional times I plane softwoods. Sharp knives and heavier cut can help.

Re: Planer problem

#8

David nailed it

Chris Knob

>This is a wood problem often seen in cathedral grained coarser woods like oak, ash and hickory. Chalk it up to waste...not much to do here but go for new stock.

Re: Planer problem

#9

Alan Young

A welcome voice from the past!

Alan Young

>Yo Chris -Good to see you!

Time to see a finished piece from your shop!

Alan

Re: Planer problem

#10

Re: A welcome voice from the past!

Chris Knob

>Hey Alan!!! Not too much coming out of my shop the last few years. I had to move it into my basement and my wife is a psychiatrist who sees patients out of our home so the days of 12 hour obsessed "Jesus, I forgot to eat today" woodworking are long gone. Few little "honey do" things here and there but that's about it. I do miss the passion and I've learned passions have appetites that need to be fed. Without regular thrills and chills from the raw material and a beautiful creation stoking the flames on a regular basis, it's tough to keep the woodworking mojo alive. I'm on the cusp of making perhaps a crazy life changing decision to go to medical school at a very advanced age. Twenty years of Infectious Disease research has left me bored and wondering "what's next?" I need a career challenge. Perhaps humping through the obstacle course of a medical education and residency with kids half my age will be more than just a challenge but I'm seriously considering it. Looks like that woodworking mojo will be on hold 'till retirement. Thanks for taking the time to chime in. Yoyur stuff always inspired me!

Chris

Re: Planer problem

#11

Alan Young

Blatant Hijack..."Infectious Disease"?

Alan Young

>Isn't that what woodworking is? :^)

Well if I read it correctly you have the one necessary ingredient to change to woodworking full time- A wife with a JOB!

Seriously-Miss seeing your stuff. Keep us posted if when you head back towards the road of cap and gown.

Alan

Re: Planer problem

#12

Re: Blatant Hijack..."Infectious Disease"?

Chris Knob

>You're right about the wife with a job but unfortunately, being married to a physician isn't a ticket to easy street anymore especially in psychiatry where changes in mental health health care have made it a $100,000 to $125,000 a year job. Now I'm not crying the blues that being the husband of someone who makes that kind of scratch isn't a great place to be, ...but with one kid in an Ivy league school and a fat mortgage, it's not the kind of money where I can kick back and enjoy hobbies. Not to mention the fact that my wife would never tolerate a woodworking "Mr Mom" husband!

Just spending the day with you guys is getting me in touch with how much I miss this place. Thanks Alan

Re: Planer problem

#13

Ditto! Having many, many Cypress projects.......

Art Silva

>under my belt I can feel your pain. Most Cypress is plain sawn, and can be a real PITA when trying to figure out which end to feed to a planer or a jointer. I have resorted to a drum sander many times to avoid a fight with machine blades. Moisture content can exacerbate the problem. Too high, and some of those beautiful cathedral heads can have a tendency to lift when the blade hits. I find that sending the board through the planer on an angle is the answer. Overall, I have milled thousands of BF of this "Eternal Wood", and have really only had a tiny percentage give me any trouble. Many boat jobs, interior and exterior house trim, and outdoor items under my belt make this the first wood I think of. My daughter's complete bedroom set was made from this wood at her request. Good luck. Art

Re: Planer problem

#14

Re: Ditto! Having many, many Cypress projects.....

matt ankney

>Hmmm.. I might just use the juniper I have been saving and save the frustration for another day, hopefully it doesn't have the same problem.. Thanks for the answers guys,, Matt