Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Looking for a motor starter wiring diagram

Posts

Looking for a motor starter wiring diagram

#1

Looking for a motor starter wiring diagram

Mike Zipparo

>I am rewiring a motor starter (Gould/ITE) on a PM90 lathe and I want to bypass the microswitch that won't let the motor start unless the speed control is all the way down. The start / stop switch has four wires, two normally open (NO) and two normally closed (NC). The starter has L1, L2, L3 (input?), T1, T2, T3 (to motor?) and other contacts labeled 2, 3, Z, X, and Y. Some of the other contacts are already connected to other contacts in the starter.

Can someone provide a wiring diagram showing how to connect the start / stop switch to the starter? Anyone know of a source for heater elements for when I up the motor HP?

Thanks in advance!

Mike

Re: Looking for a motor starter wiring diagram

#2

Re: Looking for a motor starter wiring diagram

Rick Christopherson

>I don't know your specific lathe, but my Oliver lathe had a similar switch that I also bypassed. My switch was slightly different from yours in that it shut down the motor when the speed control was set to zero. (I suspect the original function of the switch was the same as yours, but a previous owner mistakenly connected mine in series with the OFF button instead of the ON button.

Bypassing your switch will be easy, you just need to connect the two wires together permanently.

This switch is connected in series with the ON push button, and is closed when the speed is set to zero, thereby enabling the ON button. When the control is not in the starting position, this switch opens, which disables the ON pushbutton.

Re: Looking for a motor starter wiring diagram

#3

I have a PM 90 *LINK*

Eddie Pacheco, San Jose, Ca.

>It sounds like you have a 3ph machine. I'm getting ready to get rid of one that was converted to single ph. 220v and the low voltage start circuit was missing. The previous owner wired each leg of the 220 to the micro switch. He also replaced the original 2hp motor with a newer one that was shoe horned into the mounting location within the bed. (Early versions had the motor tucked under the headstock within the bed.) The wiring was a mess and dangerous to say the least.

Last week I got a 2 hp magnetic switch from Grizzly and am in the process of rewiring the whole setup now. I plan on not using the micro switch asm., but leaving it in place.

While I purchased a VFD and 2hp mtr for this lathe, it will not installed, and will be saved for another project. I just want to get this lathe out of my cramped garage/shop.

Here's a link to a 3ph. circuit that shows the wiring. The diagram is located on pages 238 and 239.

http://books.google.com/books?id=grl_sNGEOiIC&pg=PA239&lpg=PA239&dq=low+voltage+motor+start+circuit+schematics&source=web&ots=9-h3fK8fsj&sig=VRusbcFjzUZdACyzNU5i1FSiZXY#PPA238,M1

Here's another one that gives a brief explanation of a typical motor start circuit.

http://www.pge.com/docs/pdfs/biz/power_quality/power_quality_notes/motors.pdf


http://books.google.com/books?id=grl_sNGEOiIC&pg=PA239&lpg=PA239&dq=low+voltage+motor+start+circuit+schematics&source=web&ots=9-h3fK8fsj&sig=VRusbcFjzUZdACyzNU5i1FSiZXY#PPA238,M1

Re: Looking for a motor starter wiring diagram

#4

Re: Looking for a motor starter wiring diagram

Keith Newton

>I didn't see what kind of switch you were planning to use, but this would vary depending on what you chose.

I would not want to live with that switch either, but if I were planning to use this lathe for hollow turning, I would use a foot switch. One of them is momentary contact, which means that I have to hold it down with my foot for the motor to run.

I like the one on my big lathe better. it is foot activated also, but is a toggle. IF it is off, and I touch it will start, the next depression turns it off, etc. this is handy if you have a ridge along an almost finished thin side. I can find it with the tool tip while it is off, and then turn the tool on without moving a muscle, and no worry about whether I am in the right place when the tool touches. Make sure to get one with a protective shroud.

Re: Looking for a motor starter wiring diagram

#5

Re: I have a PM 90

Mike Zipparo

>Thanks, Eddie. Helpful stuff, but...The electrical motor controls reference has some good fundamentals but no detailed schematics that show the starter and controller. The Basic Industrial Electricy reference looks pretty comprehensive, but the preview from your link doesn't show p238 and it looks like the control device shown in the schematic on p239 is for a 2-wire device. My control device has two buttons (start and stop) and four wires. I don't want to be a PIA, but any idea what to do with the four wire setup?

I suppose I could figure it out by trial and error from the info that you supplied.

Thanks!

Mike

Re: Looking for a motor starter wiring diagram

#6

Re: Looking for a motor starter wiring diagram

Mike Zipparo

>Thanks, Rick.

I'll need to look more deeply, but I think the microswitch on the PM90 is not as simple as the one on the Oliver. The manual describes a two position switch. I tried to figure it out by measuring on resistance and continuity, but I couldn't get good readings.

Mike

Re: Looking for a motor starter wiring diagram

#7

Re: Looking for a motor starter wiring diagram

Mike Zipparo

>Thanks, Kieth,

I had not considered a foot activated switch, but it does sound like a good idea and the ON - OFF alternating would be the way to go since you want to be able to move around some when it is running. Can you provide specifics on which switch you used?

Thanks!

Mike

Re: Looking for a motor starter wiring diagram

#8

Re: Looking for a motor starter wiring diagram

Keith Newton

>I think I got it from Graingers, and don't have a link for you, but I think it is just called a foot activated toggle. If you are just using it with a magnetic starter, you just wire it in between L1 and the coil.

Don't even think of using it without the protective shroud. Even then, I have gotten on it by mistake, but I would still rather have it than having to reach for a switch, then find where I want to engage the work when working in a hollow.

Re: Looking for a motor starter wiring diagram

#9

Doesn't matter

Rick Christopherson

>It doesn't matter that the switch is listed as two position, and most microswitches are by the way (one normally closed and one normally open contact). The switch is controlling your magnetic starter, and this is simple relay logic (i.e. early computers). I think you may be needlessly over complicating this.

Your On button is in parallel with the low-voltage starter contacts. When the ON button is pushed, you manually close the relay contacts, which backfeed to the relay coil. When the relay is energized, then it closes the contacts. This is the self-sustaining part of the starter. When the Off button is pushed, you break the circuit between the contacts and the coil, and this interrupts the self-sustaining circuit.

In order for an exterior switch to prevent the motor from being started, but does not cause a running motor to stop, then that switch must be normally closed and in series with the On button. Any other combination would also cause a running motor to stop, and as you have already seen, that is not how this switch functions.