Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

OT Cutting Ceramic Tile

Posts

OT Cutting Ceramic Tile

#1

OT Cutting Ceramic Tile

Ken Krawford

>I'm finishing a counter top with ceramic tile and have to cut tiles that go around a 21" diameter cut out. I bought a Bosch jig saw blade that claims to cut tile but isn't working.

I know the answer but I'll ask anyway: Is there a router bit (solid carbide) that would cut this without self destructing in 3 minutes?

Any other suggestions?

Thanks.

Re: OT Cutting Ceramic Tile

#2

Speed kills

Lee Schierer - McKean, PA

>The carbide blades for the jig saws work great, but get too hot and wear out quickly. Cutting slow prolongs life, but also takes a lot longer. You can use a glass cutter and a wet saw. Use the glass cutter to scribe the desired arc on the tile face then use a wet saw to cut radial slots close to the arc in the waste piece. Then snap off the small triangular shaped pieces with a pair of tile pliers or nippers.

Lee

Re: OT Cutting Ceramic Tile

#3

Re: OT Cutting Ceramic Tile

Bill Hammond, Oregon Coast

>About 50 bucks at harbor freight, a little more at the BORG. Little tile cutting table saw, good for the straight cuts and freehand the round corners by making many cuts into the line and then breaking out the pieces and grinding it smooth. The saw uses a pan of water to cool the blade so wear your rain coat. I have one in storage if ya want to stop over you can borrow it.

Bill who on a sunny day is dreading the arrival of the rains

Re: OT Cutting Ceramic Tile

#4

ditto...

Bill Schreiber, Litchfield, NH

>I have the same el cheapo unit from the borg. It does a decent job although slow.

Good luck.

Regards,

Bill

Re: OT Cutting Ceramic Tile

#5

Re: OT Cutting Ceramic Tile

John E

>I had good look using a diamond blade attachment for a Roto-Zip. (Not the tile cutting bit - that's only OK for thin wall tile.) Cuts dry, so makes a LOT of dust - must be done outside!

John

Re: OT Cutting Ceramic Tile

#6

Re: OT Cutting Ceramic Tile

Jim Dillon

>Ken,

As others have said, treat yourself to one of those inexpensive tile cutting saws for under $100. Bought one about 5 years ago expecting the worse. Well, after doing a bathroom and kitchen, the thing is still going strong and I just used it this past year to lay a 400 square foot tile living room floor in our cabin. Did it on the diagonal so that meant roughly 80 1-foot square pieces had to be cut on the diagonal for the outside edges. Amazingly, the saw is still working fine. It is a wet job; be sure to wear safety goggles. Follow Lee's directions for cutting the arc and you will be done in no time at all.

Jim

Re: OT Cutting Ceramic Tile

#7

Re: OT Cutting Ceramic Tile

Ron Hildreth

>Bill wrote " The saw uses a pan of water to cool the blade so wear your rain coat.

I had to laugh at myself when I read that. We decided to tackle our kitchen tiling project this last summer, right at the hottest time of the year. Too hot to wear a raincoat, so I decided to wear just a pair of cut-off jeans and a smile. After cutting the first tile, the smile was gone---man, that water was cold!! By the time I had all the tile cut, I looked like I had been wrestling alligators in the swamp! What a mess!

Ron in Iowa

Re: OT Cutting Ceramic Tile

#8

Or

Mark Mandell - Gone Round In Jersey

>You can go rent a wet saw as I did. Cost me $40/day for the saw and $10-12 for the wear on the blade. The little ones will do the job, but the 10" rentals are way faster and easier.

mm

Re: OT Cutting Ceramic Tile

#9

Try the Borgs?

Nat Robison

>The Lowes and HD near me both have big wet saws in the stores and will generally make free cuts (on tiles that you bought there). If you didn't get your tiles at either of these places, my point might be moot. It's not the same as having a saw on-site but it sure helps when you only have a couple of straight cuts to make.

Even if you didn't get your tiles at a Borg, try anyway. They might cut them for you.

Re: OT Cutting Ceramic Tile

#10

Re: OT Cutting Ceramic Tile

Kneale Brownson awaiting snow in N. MI

>You forgot to stand upwind of the saw, eh?

Re: OT Cutting Ceramic Tile

#11

Re: OT Cutting Ceramic Tile

Gary Camp. Bend, Oregon

>I was in my local tile, carpet, laminate industrial wholesale house last week. The had a tile saw that looked kinda like a scroll saw with a round diamond? blade. They had cut very intricate shapes out of hard tile. They told me it would cut quarry tile. I didn't get a brand but you might check in with the local tile wholesaler. They might know of a rental saw in the area.

glc

Re: OT Cutting Ceramic Tile

#12

Re: Stopping fast kills :-p

Brian in Brighton

>But to answer the problem. I used a tile saw to get close and then went after my stationary belt sander to finalize the curve. Worked well, but probably depends on the tile material.

Brian in Brighton

Re: OT Cutting Ceramic Tile

#13

50 cents per cut

Mark Goodall - ATL - tooljunkie

>The ones areound here cut them for about 50 cents (or maybe 25) each cut.

Happy Woodworking!