Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Planer questions

Posts

Planer questions

#1

Planer questions

Nathan

>I was planing some 1" x 6" pine stock and encountered some sticking and snipe. Two questions for the more experienced planer operators out there:

1. Does high sap content in a pine board make it more likely to stall in the planer? I waxed the planer table and cleaned the rollers prior to running this stock. Still, some of the boards would stick like crazy. Two boards in particular were major culprits. They seemed to be denser than the others, and stickier to the touch. How to prevent this? Like I mentioned above, I applied wax (the liquid floor kind) to the table prior to running the boards, so I was suprised by how much they stuck.

2. I got snipe on the ends of many of the boards. I had not jointed the boards prior to planing, so I suppose some of them could have been slightly bowed, but all in all they are quite straight and flat (these are offcuts of T&G floorboards that I was planing down to use as stickers). I hadn't had a snipe problem on the planer before, so I'm at a loss how to explain this. What to look for as a cause?

The pine I'm planing has a moisture content of 11%. Is this too high? I made a big batch of stickers before by resawing from 8/4 stock with a moisture content of 9%. They were 2" wide and planed just fine, though I was taking lighter cuts. This problematic stock is 6" wide and I was taking off 2mm (a little over 1/16") at a time.

Any comments appreciated. I wish I could get to the bottom of this.

Nathan

Re: Planer questions

#2

Planer answers

Link Van Cleave

>Hi Nathan,

Yes it is common to have resinious boards stick. With my planer all the wood sticks after running resinious boards. I would use a paste wax like johnsons. Wax your beds and the pressure bar and chip breaker. Sap can build up on these as well. Clean feed rollers with alcohol.

The wood being sticky can cause snipe-ing. Gently lift the board from the back of the board as if first enters the planer and lift from the front as it exits. You have to act as a spring loaded extention bed so to speak. Also you can feed one board right behind the other. I am sure you know this and these aren't reasons for the snipe-ing only fixes but if your planer only snipes on sticky boards that is the problem !

11% is not too high by any means. I wouldn't even think about water untill you get to at least over 15% The bottom of this is sappy wood. When you are through with this project clean everything well and wax again. I call wax the best planer tune up there is. Also if you have bed rollers setting them up a bit can help with rough, wet and or resinious wood. You will get more snipe though. I keep mine down and fight with the sticky wood and clean when through.

Link

1. Does high sap content in a pine board make it more likely to stall in the planer? I waxed the planer table and cleaned the rollers prior to running this stock. Still, some of the boards would stick like crazy. Two boards in particular were major culprits. They seemed to be denser than the others, and stickier to the touch. How to prevent this? Like I mentioned above, I applied wax (the liquid floor kind) to the table prior to running the boards, so I was suprised by how much they stuck.

2. I got snipe on the ends of many of the boards. I had not jointed the boards prior to planing, so I suppose some of them could have been slightly bowed, but all in all they are quite straight and flat (these are offcuts of T&G floorboards that I was planing down to use as stickers). I hadn't had a snipe problem on the planer before, so I'm at a loss how to explain this. What to look for as a cause?

The pine I'm planing has a moisture content of 11%. Is this too high? I made a big batch of stickers before by resawing from 8/4 stock with a moisture content of 9%. They were 2" wide and planed just fine, though I was taking lighter cuts. This problematic stock is 6" wide and I was taking off 2mm (a little over 1/16") at a time.

Any comments appreciated. I wish I could get to the bottom of this.

Re: Planer questions

#3

Re: Planer answers

Nathan

>Hi Link, thanks for the excellent and helpful reply. I had not been cleaning or waxing the chip breaker and pressure bar. Now I can see that could contribute to the sticking. I'm thinking the wax I'm using might be part of the problem, too. It does help somewhat with the sticking, but it's just not slippery enough for the pine. Unfortunately, being overseas I can't just go out and buy some of the Johnson Paste Wax that you recommend. Do you think hard car wax or wax for skis might do the trick?

Thanks again,

Nathan

Re: Planer questions

#4

NO

Mark Mandell - Gone Round In Jersey

>Automotive waxes and polishes are loaded with silicone. They will contaminate your wood and make finishing a nightmare.

If you must, find some place that sells lump carnauba wax. Heat 1/4 cup mineral oil with a a tablespoon of turpentine or mineral spirits in a cheap pot over low electric heat *no fire here, please* and break/shave small pieces of wax into the oil, then stir to dissolve. Set aside to cool. When cool you should have a usable paste. If too hard, reheat and add more oil.

Re: Planer questions

#5

Re: NO

Nathan

>Thank you Mark. I found an art supplies store here that sells Yellow Carnauba Wax in small amounts. I'm going to go there to get it this week. Your advice really helped me - I appreciate it. I found the telephone number of the local S.C.Johnson wholesale dealership for this country but nobody answers the phone. I will cook up my own using your recipe. Thank you. Nathan

Re: Planer questions

#6

BTW

Mark Mandell - Gone Round In Jersey

>This is NOT something to cook up in the kitchen!!

Use a small hot plate outside on a fireproof surface with just enough heat to melt and dissolve the wax. No boiling here |:-O !! That way, if something does happen, all you have is a scorch mark to show for it.

Remember too that the "formula" is not set in stone. You can vary the parts until you get the paste you want. Again, just be very careful using solvents around heat.

MM

Re: Planer questions

#7

Ellis Walentine

Was the pine kiln dried?

Ellis Walentine

>You mention that you are overseas, so I don't know what kind of pine you are using or whether it was kiln dried or air dried. Air dried softwoods are well known to gum up planers. Make sure your pine was kiln dried to a temperature that was adequate to set the resins in the wood. Then it should plane fine without sticking. I imagine that this advice pertains to offshore softwoods as well as our domestic ones.

Ellis Walentine, Host

Re: Planer questions

#8

Re: Was the pine kiln dried?

Nathan

>Thanks Mark and Ellis. Mark: I will definitely follow your instructions to the letter, safety-wise and I'm looking forward to getting my planer tuned up with the new wax. I found a supplier for it and I'm trying to get my hands on a hotplate.

Ellis: I think you hit the proverbial nail on the head. I think this particular batch might be a mixture of air and kiln dried because alot of it goes through the planer just fine. But I recently bought some beautiful air dried 8/4 slabs of pine with the bark still on. (The price was right.) This stuff _really_ gummed up my sawblade. I had to take it off the saw and soak it in solvents several times. The resins came off the blade OK, though. They affected the planer too, but since I was planing 2" wide strips only, it wasn't so bad. These 5-6" boards have triple the surface area, and maybe some of the resin remnants from the previous batch are still there, causing trouble.