Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Performax Speed

Posts

Performax Speed

#1

Performax Speed

Doug Reynolds in Seattle

>I am using my Performax 16-32 to do some "Jointing/planeing" of boards too wide for my 6" jointer, especially following panel glue-ups. This is not rough wood from the mill but, more like S2S. Taking real light cuts with 120 grit, what is the most desirable feed belt speed? Is burning, on cherry for example, more likely at slow speeds?

I would think a slower speed would result in greater consistency of thickness and better overall quality but, I think the manual says to run at highest speed possible.

Once I have the boards flat, what is the best way to remove the sanding marks which tend to be pretty deep? Random orbit sander does not work very quickly. But, I do like the flatness of the panels over the results I might get with a belt sander.

Re: Performax Speed

#2

Re: Performax Speed

Mark Mandell - Gone Round In Jersey

>Doug,

Your issue, in my experience, is a trade-off depending on the wood. Sweet and/or resiny/sappy woods like cherry, sugar maple, pine and firs are more likely to develope streaks that will burn into the wood and your abrasives. My basic rule of thumb is to take the lightest and fastest cuts you can do, flipping the workpiece after each pass. The idea is to heat up the wood as little as possible; less friction equals less heat. I also clean the abrasives after several passes to make sure that the belt isn't loading up. I also watch the wood on the outfeed side carefully for any sign of darkening, ready to drop the table or kill the drum to halt a burn.

Hope this helps

Re: Performax Speed

#3

Re: Performax Speed

Paul Woolson

>Drums can be very finicky things. You best option is a VERY light and fast pass. You shouldn't hear the motor labor at all when you enter the wood. The only difference in sound should be the paper making contact with the wood.

And yes, as the manual says, run it wide open.

As for the scratches: I wouldn't think 120 would leave much that couldn't be hand sanded easily. But if that's the case, maybe put some 220 on the 16-32 and finish it off with that.

Re: Performax Speed

#4

Re: Performax Speed

Barry Irby

>I agree, faster lighter passes. Coarser paper. I find 80 grit to be more useful than 120. Try 80, 120, 220. Ninety percent of the work with the 80 and a pass or two each with the others to clean up the scratches.

I watch the coupler on the motor to the drum shaft. It has black and white markings and it strobes in fluorescent light. You can see if the motor starts to slow, Either slow the feed down or lighten the pass. I take less than a quarter turn off each pass. Run the last two passes with it set in the same position.

Re: Performax Speed

#5

PS

Mark Mandell - Gone Round In Jersey

>Forgot to mention that you may do better if you run your board through at an angle (using the entire width of the drum) then on the next pass on that same side, angle it the opposit way (so the scratch pattern form an "X"). This was passed along to me by the JET tech when I bought my machine. The idea is to not have the abrasives running in groves parallel to the grain until you get above 220 grit on the drum. I tried the "abrasive planing" routine with 36 grit; took huge amounts of time and runs to clear out the deep scratches. Took my boards back to the planer with tear-out preventer applied to hog off the heavy reductions.

mm

Re: Performax Speed

#6

when you switch

Michael Dresdner

>I agree with all of the above -- very light passes, diagonally, at the fastest speed. I also run each board twice at the same setting rather than changing it with each pass.

>> Once I have the boards flat, what is the best way to remove the sanding marks which tend to be pretty deep?

I find with the Performax that you must go down one grit when you switch from drum to ROS. Hence, if you are using a 120 belt, start ROS sanding at 80 grit. This is largely because belt grits are cubic, blocky grits that leave a deeper groove than the sharp, triangular grits on ROS disks and hand sheets.

Re: Performax Speed

#7

Re: when you switch

Sue McLam in Orange, VT

><< I find with the Performax that you must go down one grit when you switch from drum to ROS. Hence, if you are using a 120 belt, start ROS sanding at 80 grit. This is largely because belt grits are cubic, blocky grits that leave a deeper groove than the sharp, triangular grits on ROS disks and hand sheets. >>

It's interesting to hear you say that Michael as I have found the same thing to be true and wondered if it was just me. I always sand with 80, 120, 150 and 180. I often have to then start my ROS sanding at 150, sometimes I can start with 180, depending on the wood. I use to try to start my ROS at 220 and it just didn't cut it (pun intended!).

Sue

Re: Performax Speed

#8

Question for Mark

Jesse Cloud

>"Took my boards back to the planer with tear-out preventer applied to hog off the heavy reductions."

Hey Mark,

What is "tear-out preventer"? I sure could use some of that!

Re: Performax Speed

#9

Gotcha!

Mark Mandell - Gone Round In Jersey

>Tear-out preventer is a magical liquid the I have never seen sold by woodworking suppliers, either clicks, bricks, or both. You can, however, find it most everywhere else, in one form or another.

QUIT JERKIN' MY CHAIN, MANDELL!!!!!

OK,OK . . .

It is, in short a light mist of H2O, agua-pura, well-gin, water applied to the board's surface just before you feed it through the machine. Apply the mist evenly to uniformly moisten the surface to be cut. Will soften the fiber just enough to reduce tear-out by 80% or better unless you're trying to machine plane bird's eyes or burls.

Try it, you'll like the flavor.

|;-}}}}

mm

Re: Performax Speed

#10

D'oh!!

Jesse Cloud

>