Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Your opinion is needed? (Cabinet table saw)

Posts

Your opinion is needed? (Cabinet table saw)

#1

Your opinion is needed? (Cabinet table saw)

Sam Aloni

>I just came across a very good deal on Delta Unisaw.

It is a 5HP saw, about 1 year old and the price is $700.00.

So far I have most of the tools (Planner, jointer, band saw, and a small 1HP table saw).

My table saw is 50 years old, I use thin blade on it and it does the work. I mostly cut 4/4 wood.

My Question is: I can afford to buy it but should I spend the money on it? (I would also have to run a new breaker box in my basement with 220V).

Would you buy this saw?

Thanks

Re: Your opinion is needed? (Cabinet table saw)

#2

Re: Your opinion is needed? (Cabinet table saw)

Michael Wangler in Rochester, NY

>Sam,

That sounds like a pretty fair price for that saw. The new wiring should be pretty easy. If you have the $$ and the room I say go for it. A new saw would easily cost you double that price.

Michael

Re: Your opinion is needed? (Cabinet table saw)

#3

Re: Your opinion is needed? (Cabinet table saw)

Larry Clinton

>On the face of it, sounds like a great deal. I would make sure it is a Unisaw. Delta did sell a "cabinet saw" in the last couple of years that is NOT a Unisaw, but more of a hybrid saw. I would not pay $800 for that saw (even new). I don't know if the hybrid was available as a 5 hp saw though. I would look the saw over very closely as the price is pretty low for a 1 or 2 year old saw. Why is the seller getting rid of it? I would check the table for flatness etc. If it is indeed a Unisaw, and in new condition with original fence (either the Bies or Delta) I would certainly buy it for that price.

Re: Your opinion is needed? (Cabinet table saw)

#4

Re: Your opinion is needed? (Cabinet table saw)

Sam Aloni

>I am sure it is a unisaw. I check the modle # and it was Model 36-L51X-BC50(Delta X5 5 HP, 230V, Single Phase, Left Tilt Unisaw w/ Biesemeyer. It looks in a very good condition, I did not check if it is flat.

Re: Your opinion is needed? (Cabinet table saw)

#5

Re: Your opinion is needed? (Cabinet table saw)

woodtrekker

>Sam Selling for 50% off, I`d be looking it over very good. Some of these newer so called unisaws are made in China, and I wouldn`t buy, and I believe they are around 50% of the USA made saw, If they even have any made here anymore. If it is made here in the states and there is nothing wrong with it, it is more than worth it. I`d even buy it. Larry in Ohio

Re: Your opinion is needed? (Cabinet table saw)

#6

Re: Your opinion is needed? (Cabinet table saw)

wilbur

>What kind of table saw do you currently have? Some of the older woodworking machines were built better than their modern day equivalents.

Re: Your opinion is needed? (Cabinet table saw)

#7

Re: Your opinion is needed? (Cabinet table saw)

Bill Schreiber, Litchfield, NH

>If there are no problems with it, that is a great deal. Even paying for a new circuit to be installed, you are still coming out ahead ofthe game unless the saw is totally beaten on (can't imagine how anyone could, they are built so solid).

Bill

Re: Your opinion is needed? (Cabinet table saw)

#8

Re: Your opinion is needed? (Cabinet table saw)

Sam Aloni

>I have Sears 1Hp table saw. built in 1954.

Re: Your opinion is needed? (Cabinet table saw)

#9

buy it!

Dan Manturi

>5HP unisaw, left tilt, Bies fence for $700? BUY IT! I do not think the hybrid came in 5HP.

to run my 220v load center to my garage it cost me about $200. i did the labor. Wire was $2 a foot for #6 copper, load center panel with breakers about another $50, assotred plugs and stuff another $30.

I sold my old Delta contractor saw and biesmeyer fence when i got my used 3HP right tilt Unisaw with Unifence. I HATE the unifence.

I'd grab this one. Sell the old Sears for $100 and use it toward your wiring.

Dan M.