Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

trunk design question

Posts

trunk design question

#1

trunk design question

Bill Tindall, E.TN

>I want to build a trunk with a curved top, pirate chest sort of thing, for a toy box. I have never seen one except in cartoon pictures. I can figure out how to make the box and even the curved top, but how are the ends filled in, what would be gables were it a house? I am stumped at how to join the "gable" to the top to make what would be the lid. A picture, plans or a description would be appreciated.

Re: trunk design question

#2

Re: trunk design question

John Veerkamp

>Bill,

I've seen them where the staves were glued and nailed with brass nails on a curved end piece. I've also seen them where an iron band was wraddep around the curve and Nailed or screwed down.

John

Re: trunk design question

#3

Re: trunk design question

Kelby

>I built the steamer trunk from the Rockler plans and was very hapy with it.

http://www.rockler.com/product.cfm?page=431

Re: trunk design question

#4

Re: One of the Norm reruns on DYI

Glenn Madsen near San Francisco

>this week was building a chesnut version of a steamer trunk, iron bands and all. Nice project.

You can likely order measured drawerings off of his site, should you need them.

Nahm used through dovies with his Omnijig, and built a chest like you describe. A bump rail at the bottom, and screwed on bun feet

Re: trunk design question

#5

Re: trunk gable

Kneale Brownson awaiting snow in N. MI

>Sometimes just a solid piece of whatever wood you're using. Sometimes that solid piece covering the end grains and a smaller piece inside to support the slats that make up the top.

Re: trunk design question

#6

Re: trunk design question *LINK*

Ron Hildreth, Alta, Iowa

>Bill,

I have a set of plans from Meisel Hardware, but not sure if it has the curved top you speak of. I'm just now going to work, but will look when I get home tonight. Otherwise, Meisel has several plans for trunks of varying designs and sizes on their website;

Ron in Iowa


Meisel Hardware

Re: trunk design question

#7

Re: trunk design question

Bruce, a MN Galoot

>The most recent show (at least that I saw) of David Marks' series was of a trunk just as you describe. He laminated the top from bending poplar and formed it with vacuum pressure. IIRC, it had a "gable end" but he laminated some really nice veneer over the top of it all, so the joint at the end wasn't so obvious.

Bruce

Re: trunk design question

#8

Re: trunk design question

Paul in NJ

>Hi Bill,

Years ago, I built a hope chest for my wife that had a curved top (but not as exaggerated as a "pirate chest"). The top was coopered: five boards whose edges planed at a slight angle, glued, and then planed and sanded to a fair curve. The front and back panels were frame and panel construction. The sides were glued-up panels (no frame), their tops cut to match the curve of the top. The grain of the sides ran vertically. The bottom (also a glued-up solid panel) was doweled to the sides a couple inches up from the bottom of the sides. The front and back were simply glued to the sides and bottom. The grain of the bottom ran from side to side. I was able to eliminate cross-grain expansion and contraction problems using this construction.

Paul Dzioba

Re: trunk design question

#9

Re: trunk design question *LINK*

Ron Hildreth

>Bill,

I checked the trunk/chest plan I had , but it has a flat top. You mentioned a pirate treasure chest, and found this at Meisel Hardware. You can buy just the plans, or plans and hardware kit.

Hope this helps

Ron in Iowa


Pirate Treasure Chest