Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Which bandsaw blade(s)?

Posts

Which bandsaw blade(s)?

#1

Which bandsaw blade(s)?

David Hay @ Denver

>I'm in the market for a bandsaw. I think I've got it narrowed down to the Rikon Deluxe 14" (10-325)...however I'm now reading up on the various blades and I'm somewhat confused on what would be a good blade or two start with. Can anyone recommend one or two blades that are good "general purpose" blades? I know the answer somewhat depends on what I'm planning to do...In my case, some occasional curve cutting but also some resawing from time to time. Is there a good "starter" set of blades? Width? TPI? Tooth style?

Thanks!

David

Re: Which bandsaw blade(s)?

#2

I prefer Timber Wolf from Suffolk Machinery *LINK*

David Barnett - SW Florida

>I love these blades. Because these require less sawing tension (Swedish silicon steel) than other blades, they're easier on the springs, bearings and tires. They are very sharp, hold their edge longer than several brands I've tried (Lenox and Starrett are very good, too, however). The price for steel (the NEW precious metal) is getting up there as of late, so recent prices for Timber Wolf blades reflect this trend. That said, I wouldn't buy any other. I use them for ripping and resawing mostly (3/4" 3AS-Special on my 16"), and prefer 3tpi for both. Get the widest for which your bandsaw is rated.

The 1/2" 3PC is great for stacked boards and I often use my 3/8" 4PC for ripping thinner stock.

I also use TWs for thick aluminum, as they cut nicely with a slower feed rate. Lubricate the blade with a lump of tallow for best performance. Starrett makes a superb blade for nonferrous metals, too, which I find works better on brass but TW does an acceptable job.

Opinions will naturally differ, but this is what works for me.


Timber Wolf bandsaw blades

Re: Which bandsaw blade(s)?

#3

Re: Which bandsaw blade(s)?

Clint Searl, at the base of Haycock Mtn

>Timber Wolf 1/4" 4TPI for gen'l purpose

Olsen 1/2" 3TPI carbide tipped for resawing

Clint

Re: Which bandsaw blade(s)?

#4

Re: Which bandsaw blade(s)?

knotscott

>I haven't tried alot of the top choices, but I've been pleased with the Timberwolf blades from Suffolk Machinery.

One aspect that I really liked, is that they asked alot of questions about my saw and what I cut, then made a suggestion for a set of blades. They were having a buy 3, get one free deal too..."code 443". Four blades were ~ $50 shipped.

Re: Which bandsaw blade(s)?

#5

Re: Woodslicer from Highland Hardware

Larry Clinton

>I have used the Timberwolf blades - they are a great blade. I also purchased the Woodslicer from Highland Hardware and IMHO they are a little better blade than the Timberwolf. I had used the Timberwolf on my old Crapsman saw. I read some reviews in one of the mags (can't remember which) which rated the Woodslicer just a cut above the TM for finish - I bought both the 3/4 and 1/2 inch blades for my MiniMax MM-16 and really like the finish. I have the 1/2 installed now and have cut both green wood and dried White oak and Walnut (up to about 12" thick). If you are planning to cut real tight radii, you may want to also buy an 1/4" or even an 1/8" blade. For a 14" saw, I personally would use the 1/2" woodslicer for general use.

Re: Which bandsaw blade(s)?

#6

Second that

Denis Ch�nard, Orl�ans, Ont.

>I used TW in the past, but when I tried the WS all of a sudden I was in a new ball park. Cuts faster, surface finish is noticeably nicer, and it is quieter to boot (probably because of the variable pitch).

WoodSlicer is definitely "a cut above" :-)

DC

Re: Which bandsaw blade(s)?

#7

Re: Which bandsaw blade(s)?

Bill Falberg

>Here we go again; comparing apples to oranges; praising this blade over that one without reference to any of the cut parameters; and worst of all recommending X blade widths for Y radii cuts when we already know that some 1/2" blades can cut 1"D plugs while some 1/4" blades can't turn inside a coffee can. If there's to be only one *BEST* blade; it's the one you, yourself, set for the job you, yourself, are doing. So much is determined by the quality of the saw and the skill of the operator that such a question is as meaningless as the answers. Garrrrumfffffffff!

Re: Which bandsaw blade(s)?

#8

Re: Which bandsaw blade(s)?

Clint Searl, at the base of Haycock Mtn

>Short of actually evaluating many blade configurations in namy scenerios, which probably would not be worthwhile for the hobbyist, for the level of work most of us do, the opinions expressed above are valid, being based on the experience of respected WC regulars.

Clint

Re: Which bandsaw blade(s)?

#9

1" plugs with a 1/2" blade?

Denis Ch�nard, Orl�ans, Ont.

>That, I'd really like to see!

Does that blade cut a 1/2" kerf? :-)

DC

Highly skeptical here

Re: Which bandsaw blade(s)?

#10

Re: Which bandsaw blade(s)?

Larry Clinton

>Bill, I don't want to get into a huge disagreement with you. I don't agree with many of your beliefs - including the fact that a 2 wheel bandsaw is not as good as a three wheel for most applications. (I'm quite sure Do-All and a few others that are not producing "hobby" saws would be selling 3 wheel if they were better). I also recognize that if you put a lot of set into a blade it will be great for some applications. Cutting curves, wet wood etc. However for general use in a woodworking shop, where most of us use a limited number of factory produced blades. Most of us (99+%) are not going to reset the teeth or resharpen the blade so the advice given above is valid. The Wood Slicer is a variable pitch 3 ~ 4 tooth per inch blade with extremely sharp edges and teeth are hardened to RC 65 ~ 67. This blade will adequately handle most of the cutting needed in the average shop. I do not intend to cut barn beams or use my saw to produce railroad ties. I use it for veneer, smooth cutting of dried hardwoods and occasionally roughing a blank for a lathe. By the way, I designed, built and debugged automation equipment for about 40 years. The equipment included many crimping, cutting, spinning, ultrasonic welding, bending, forming, orbital staking, induction welding, automated placement, soldering and testing. I have been the Engineer over a fair sized punch press department as well as an injection molding department with 85 presses. So I am not a novice in equipment design or use. And YES, I can properly operate my bandsaw, as a trial I cut some veneer off an 8" board about .015" thick X 14" long. My MiniMax MM-16 does everything I want it to do in my shop using the blades I recommended above. Please, lets agree to disagree without posting comments like you did above. Thanks

Re: Which bandsaw blade(s)?

#11

Re: Which bandsaw blade(s)?

Bill Falberg

>Sorry about my didactic writing style, I guess it can sound caustic sometimes. I'll try to soften up a bit. I never said three wheelers are "better" ; just "bigger". In fact I plan to market a line of two-wheeled portables, Falberg Lite, for those who don't need the full-on monsters I presently sell. And I don't expect to see most folks beating out blades or rounding off trailing edges to decrease a blade's radius ; but for those 1% who need drastic measures to get it done, I'm trying to fill in the blanks. I do feel there's a general void in the average BS operators' understanding of blade dynamics that my research could help to fill and if anybody profits from it then I'm a happy guy. As an engineer you must appreciate the value of exact definitions when discussing technical stuff and I thought I was helping and I'm sorry if anyone took offense. Perhaps, in the future, I'll label such postings as OT or under Trivia. Or, if nobody cares, I'll stop altogether. It's just my 2 cents.

Re: Which bandsaw blade(s)?

#12

Re: Which bandsaw blade(s)?

Larry Clinton

>Bill, I am also sorry I came back so strong. I do realize you know much more about bandsaws and blades than I do. But I guess I feel that when someone asks about changing a bearing in a table saw etc., they really don't want me to tell them about all the grades of bearings available, the possibility of adding a pressurized lubrication system and other items that would just confuse the average woodworker. I also realize my answer and recommendation for the blade left out a lot of information. However, I don't believe this information would be real beneficial to most people. I think the person who asked the question was wanting to purchase a general purpose blade that would handle most tasks pretty well. I do think the Wood Slicer fits that bill. I am sure you could recommend the proper blade for each task IE: 4/4 hardwood straight cuts - radius cuts - 12" and over veneer cuts with thin kerf, Green wood cutting and tight radii cutting. This is real valuable information if a person is having a problem with a particular cut or if they are doing production work with a saw or doing repeated cutting of one type. I do read your posts and value your opinion for this type information. In reality though, I just use the one blade most of the time - I know its not the best blade for all tasks, but if the finished product turns out ok, I don't care if it takes me twice as long to make the one cut. I do the same on my Unisaw, I can't remember when I've taken the WW 2 off the saw to change to a rip blade. I do know the rip is a better choice, but in the time it would take to change the blade I am through with the sawing. I think this is the difference in professional woodworkers (and sawyers) and amateurs like me. Please don't stop posting the information as your insight is valuable. Just lighten up a little on us amateurs.