Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Bandsaw fence question?

Posts

Bandsaw fence question?

#1

Bandsaw fence question?

Barry Irby

>I have a Delta 14" bandsaw with riser. I don't have a fence. I do have the fence off my Delta?Rockwell Table saw. (Saved It when I upgraded the fence)

It occurred to me that I could mount that fence on the band saw. Either just put a front pipe rail on the BS and let the far end of the fence "run wild" or cut the fence off and shorten it so the far end would clamp to a rail on the other side. I think there is enough "adjustment" in the fence to allow for drift. Does this sound like a good idea or should I skip it and keep the TS fence in case I decide to sell the TS and keep the upgrade fence?

PS, Does a BS fence need to lift off? This one slides on from the ends. What fence do you have? What would you get?

Re: Bandsaw fence question?

#2

Re: Bandsaw fence question?

Carol Reed - in Nebraska

>Short answer. Keep your fence for the TS. The only way to slide the fence off the BS would be to remove the BS blade! So yes, the fence needs to lift off.

At least in my shop it would.

Re: Bandsaw fence question?

#3

Re: Bandsaw fence question?

Kneale Brownson awaiting snow in N. MI

>I have the Delta fence on my 14-inch BS. It has two rails and the tie-down at each end to allow adjustment for drift. It has to come off the ends of the rails. The rails are perforated squares and there's an adjustment wheel to move the operator end of the fence in and out very gradually. I think jerry-rigging the TS fence to work correctly on your BS would be more work than it's worth. A wood fence and spring clamps would be quicker/easier/cheaper.

Re: Bandsaw fence question?

#4

Re: Bandsaw fence question?

JohnKJordan in East TN

>Barry,

For me, the bandsaw fence has to be quickly removeable and positionable. I remove it very often - whenever crosscutting and when cutting freehand. I also move it from one side of the blade to the other as needed.

I once bought a 3rd party bandsaw fence once which was very high quality and had good provision for resawing. However, I returned it right away when I found the trouble it was to remove and swap from the left to the right side. But if you used the bandsaw only for ripping and resawing, such a fence might be perfect. If you only used it for resawing, you might just build a fence and fasten it with c-clamps.

My bandsaw (14" Delta with riser, maybe 6 years old) has a pipe rail on the front and a flat rail (piece of angle iron) on the rear. The front of the fence slips quickly onto the pipe from either side and clamps firmly with a single lever in the front. The back has a button which rests and slides along the rear rail. There is drift adjustment built into the fence by means of two bolts on the top near the front.

I suspect you could order all the parts for the fence from Delta and install it on your saw. You may have to drill a few holes in the table. You might visit a dealer or two and look at fences on various saws.

JKJ

Re: Bandsaw fence question?

#5

Re: Bandsaw fence question?

David Yoho

>Barry, I have the Delta suppied fence on my Delta 14" and I hate it. My Minimax-16 has a much nicer fence that lifts off.

I'd keep the TS fence for the TS and buy or make one for your bandsaw. There are plenty of third party fences available for your saw. If you go this route, look for one that lifts off and is easy to add a piece of wood to the face of the fence for when a taller fence is needed.

David

Re: Bandsaw fence question?

#6

Re: Bandsaw fence question?

George@Colonel's Workshop-Havertown PA

>Good Afternoon Barry,

I recommend you use a fence designed for your saw. Keep the TS fence for TS application. I currently use a FasTTrak fence on my 14 inch Jet Bandsaw. I liked it better than the Jet 14" Bandsaw Fence which came with my saw. Both are very good features and good performers. The FasTTrak is easily and quickly removable, and you really need to remove it in some situations. The FasTTrak also has different size resaw fences, and these are also very effective and can be "micropositioned". Take a good look at the aftermarket hardware.

George

Re: Bandsaw fence question?

#7

Re: Bandsaw fence question?

Bruce Wrenn

>Barry, build yourself one of Mark Dugenskie's "Three Board Fences." They only take 3 pieces of wood, three carriage bolts, and are micro adjustable, along with adjustment for drift. The micro adjustment is in increments of 0.004" He uses post it notes for adjustment. Plans can be found in his book/ video, "Mastering the Bandsaw. "

Re: Bandsaw fence question?

#8

Thanks, everybody

Barry Irby

>