Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

rubber feet for cutting board

Posts

rubber feet for cutting board

#1

rubber feet for cutting board

Dan Collins

>Friends: I am making a couple of heavy-duty cutting boards for Christmas presents. I want to add some rubber feet to raise the board up off the countertop. I am thinking of using 4 round feet that would be about a 1/4 inch thick. I would like to be be able to screw or glue them to the bottom of the cutting board. I can't seem to find anything like this in all my woodworking catalogs. Maybe they go by a different name. Can anybody steer me in the right direction to find something like this? Thanks. Dan

Re: rubber feet for cutting board

#2

JL

Re: Would grommets work?

JL

>I used grommets from the Borg for one of my projects which required feet. Use stainless steel screws and washers though or you may end up with rusty stains (DAMHIKT).

Re: rubber feet for cutting board

#3

Re: rubber feet for cutting board

Mike Schwing from Md.

>Lowe's and Home Depot carry clear silicone rubber stick on feet. I use them on my cutting boards and have had no problems, even many years and lots of use later. Make sure the surface is clean first, wipe it with acetone and stick them right on when dry. They are quite durable and don't come off.


Re: rubber feet for cutting board

#4

Re: rubber feet for cutting board

Jim Dillon

>Dan,

I had the same experience as JL. The local Borg, if you have one, usually has an area devoted to rubber/plastic furniture sliders etc. You might find what you are looking for there, but check the product closely. A lot of time the product is a hard plastic and I think you would want a softer material. Good luck.

Jim

Re: rubber feet for cutting board

#5

Here's a different type *LINK*

Lee Schierer - McKean, PA

>If you coat your cuttin board with mineral oil, I don't think the stick on bumpers will stick very long. They make a bumper you push into a hole drilled in the bottom. See the link below fo one source.


img

Bumper

Re: rubber feet for cutting board

#6

Ellis Walentine

Another couple of possibilities

Ellis Walentine

>On occasion, I have made wooden feet for cutting boards and serving trays, and then installed regular little rubber nail-on bumpers to the bottoms of the feet. That works fine.

Another appraoch is to get some beveled faucet washers and countersink them for small brass or stainless screws. If you really want them round, you can stick a box nail through them and chuck it in your drill press, and then sand them to a rounded shape.

Both approaches are kinda fussy, but they work.

Ellis

Re: rubber feet for cutting board

#7

Re: rubber feet for cutting board

Bruce, a MN Galoot

>I've gotten some screw-on soft rubber bumpers from Menards.

bh

Re: rubber feet for cutting board

#8

Stainless Steel Screws

Howard Acheson

>Keep looking. I have found rubber feet at a number of hardware stores. I suggest you buy some stainless steel screws to replace the steel screws supplied with the bumpers. Steel will rust.

Re: rubber feet for cutting board

#9

Toilet Seat Bumpers....

Kneale Brownson awaiting snow in N. MI

>And replace the screws that come in the bumper kit with stainless ones.

Re: rubber feet for cutting board

#10

Re: rubber feet for cutting board

Robert Henderson

>I believe I've gotten feet like that at Home Depot

Re: rubber feet for cutting board

#11

Lee Gordon

Re: rubber feet for cutting board

Lee Gordon

>Several years ago I needed some rubber feet for the same purpose and found them, of all places, at Radio Shack.

Re: rubber feet for cutting board

#13

And don't tell anybody what they are. LOL

Tom Pilsbury

>

Re: rubber feet for cutting board

#14

Re: McMaster *LINK*

Bob Entwisle in NJ

>The link is to a page of push in bumpers, but they have about 10-20 pages of all manner way shape and form of rubber feet.


http://www.mcmaster.com/ctlg/DisplCtlgPage.aspx?ReqTyp=CATALOG&CtlgPgNbr=3611&RelatedCtlgPgs

Re: rubber feet for cutting board

#15

My thought, exactly! Don't use used ones.

Barry Irby

>