Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Oil rubbed bronze screws - source or method

Posts

Oil rubbed bronze screws - source or method

#1

Oil rubbed bronze screws - source or method

Peter Gregory

>I have made a number of simple pieces of wood that I screw into a wall and call done. You know, things with hooks, or rails. Often, I have used brass screws and a fancy washer, makes it look nice. Now I would like to find some screws that are oil rubbed bronze looking or figure out how to make my own. A simple internet search didn't work for me (and I'm pretty good at it).

Anyone know a source for oil rubbed bronze screws and decorative washers or how to make your own? With all the oil rubbed bronze fixtures out there, you would think they must be out there somewhere.

TIA.

Re: Oil rubbed bronze screws - source or method

#2

Re: Oil rubbed bronze screws - source or method *LINK*

Bob Entwisle in NJ

>googled it and came up with:

http://www.hardwaresource.com/Store_ViewCatLevel3.asp?Cat=493

scroll down the page a bit.

Hope this helps


http://www.hardwaresource.com/Store_ViewCatLevel3.asp?Cat=493

Re: Oil rubbed bronze screws - source or method

#3

Jamestown Distributors has it all

Clint Searl, at the base of Haycock Mtn

>

Re: Oil rubbed bronze screws - source or method

#4

Re: Oil rubbed bronze screws - source or method *LINK*

Jim Dillon

>Peter,

First off, I don't have a clue what oil rubbed bronze screws are but that's my problem, not yours 8-). Anyway, Jamestown Distributors has a large selection of brass and silicon brass fasteners and are a source that is not often mentioned as they sell to the marine industry. Here is a link to the silicon bronze fasteners and I note that they do mention the ability of these fasteners to turn color to match redwood and cedar. Good luck.

Jim


Silicon Bronze Fasteners

Re: Oil rubbed bronze screws - source or method

#5

You could patina your own...

Charles Wiggins

>I'm not sure how close it would come to what you have in mind, but here's a couple of recipes.

For golds, browns, and reds - 1/2 teaspoon Ferric Nitrate in 8 oz. water.

For golds, browns, and blacks - 1/2 teaspoon Sulphurated Potash (Liver of Sulfur) in 8 oz. water.

It's best to use distilled water so you don't have stray mineral contaminants. Warm the metal with a torch and apply with sprayer or brush. You want the metal warm enough to steam well, but not boil the mixture as it's applied.

We also used sodium thiosulfate (photo fixer) because my sculpture instructor also taught photography so it was easy to come by, but you can get wildy varied results - from greens to dark browns depending on the heat and alloy of the base metal.

Finish off with fine paste wax or other appropriate finish. We used to use One Coat brand spray plastic. Comes in a can just like their spray paint.

Re: Oil rubbed bronze screws - source or method

#6

I've used liver of sulfer on other stuff...

John in NM

>didn't work for me on brass - BUT I was using it cold, mostly on copper. So the warming step is important for some alloys.

Though the name sounds funny, it is readily available from jewelery suppliers.

Don't use inside the house, its safe enough but smells a bit like rotten eggs.

Re: Oil rubbed bronze screws - source or method

#7

Re: But, but, but - picture included this time

Peter Gregory

>I found little screws, with flat heads, in different colors, using a search engine, just like you guys did. I'm talking about something nicer. Here is a picture with examples of shiny brass screws and decorative washers. Anyone know where to get something like these in Oil Rubbed Brass looking finishes?

Thanks for the help so far. If it was easy, they would carry it at the home center and my search would be done. :)


img

Re: Oil rubbed bronze screws - source or method

#8

Re: But, but, but - picture included this time

Jim Dillon

>OK, Peter, we need to see a picture of what an "oil rubbed brass screw" should look like. Frankly, on my monitor, those look just like ordinary brass screws to me. Or maybe we need to know what you mean by "oil rubbed". I have visions of someone squirting 3-in-1 oil on an ordinary brass screw and calling it "oil rubbed" - and charging twice as much 8-). Or maybe someone squirts the oil on and heats them a bit?? Not trying to be cute here, but we would like to help out if we can.

Jim

Re: Oil rubbed bronze screws - source or method

#9

Re: But, but, but - picture included this time

Peter Gregory

>Hi Jim - Those are shiny brass screws that I have and I'm looking the same shape in a different finish. Looks like I can buy a box of brass online (searched for brass screws) and color them myself (using the chemicals listed here). My search also has located a large woodworking supply dealer, that I had never heard of, that is only 80 miles away, so that is nice. :)

Re: Oil rubbed bronze screws - source or method

#10

Re: But, but, but - picture included this time

Bill White

>ORB (oil rubbed bronze) is a dark brown to black dull finish that will have some coppery or dull brassy highlight. The faucet/hardware folks started the look. Been VERY popular.

Bill