Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Drilling a square hole??

Posts

Drilling a square hole??

#1

Drilling a square hole??

Doug in Denver

>Just for fun, I'm making a shift knob for my car out of cocobolo. The shaft is square, but not the size of any standard morticing chisel, but it's around 5/8" wide. So what is the best way to drill a square hole in cocobolo maybe 2.5 inches deep, but that does not go all the way through? I have only 2 ideas. One is use the next smaller size morticing chisel and then widen it a little with a bench chisel. But I wonder about forcing a morticing chisel through cocobolo. Two is using a round bit, then a corner chisel to square it up. Any other ideas or comments on mine?

Re: Drilling a square hole??

#2

Re: Drilling a square hole??

Barry Irby

>One idea would be to use a standard 1/4" square mortising chisel and punch a hole in each corner, and then it would be easy to use the same bit to punch out the webs between the holes.

Sharpen the bit well. Cocobolo is hard and tough.

Re: Drilling a square hole??

#3

Re: Drilling a square hole??

Bill Howatt

>You could get closer to square with a router and a small bit rather than a large round bit.

Could drill a series of small holes within the square to make the chiselling easier.

Use a dado blade or something to cut a 5/8 slot the right depth. Then glue pieces in to fill the sides. Could make it contrasting.

Bill

Re: Drilling a square hole??

#4

Those are good ideas.

Doug in Denver

>Thanks. That makes me realize there are better ways than the two I suggested.

Re: Drilling a square hole??

#5

Re: Those are good ideas.

Barry Irby

>The easiest way might be to "take the block art" and put it back together. Slice a layer off the top. Slip the bottom part in half vertically. Cut rabbets in the two halves of the bottom blocks and glue them back together. if you reassemble the pieces carefully the joins won't show much. Not nearly as much fun as leaving it in one piece.

Re: Drilling a square hole??

#6

Re: Drilling a square hole??

john lucas

>Doug If I didn't have a mortising chisel I would simply drill it close to size and then use a small chisel to clean up the corners and possibly the sides. If you use large chisel you will have to fight it. Cocobolo cuts pretty well but it is a harder wood.

If you do have a mortising chisel I would also recommend using a smaller one and drill each corner. Then if necessary clean up the sides with the mortising chisel.

Re: Drilling a square hole??

#7

Whatever the method make the hole first

Forrest Addy

>Whatever the method make the hole first. Then you can make the exterior anyway uor want it.

If the hole is an odd size I'd probably make it with a morticing chisel and use a marking medium like prussian blue to ensure a good fit. Cocobolos is not the most forgiving wood to hand work. It's brittle and full of silica which is abrasive. Keep your tools very sharp and don't try to take off too much as once.

Re: Drilling a square hole??

#8

Re: Drilling a square hole??

Dick Coers

>Here's a couple more ideas; drill a large hole so the knob will slide over the corners of the square. Fill the crescent shaped gaps with epoxy and a filler to make the square hole. The other idea is similar. Drill that large hole again, but make 4 wood fillers that will make up the round od, then a square hole.

Re: Drilling a square hole??

#9

Re: Drilling a square hole??

DB

>Did you remove the old shift knob first to verify that the end of the shifter is not actually a standard threaded connection? If it is truely square how is it held on securely?

Re: Drilling a square hole??

#10

Re: A round hole and epoxy?

Glenn Madsen near San Francisco

>

Re: Drilling a square hole??

#11

Re: Drilling a square hole??

JohnKJordan in East TN

>How about machining the metal shaft to fit your morticer, assuming that works OK with Cocobolo. Or weld/braze some shims to fit the next larger size.

JKJ

Re: Drilling a square hole??

#12

Re: Drilling a square hole??

RSC Furnishing Design

>Why not just drill 4 - 3/16' mortises in each corner of the 5/8" hole - that all meet in the middle - Duh!

Re: Drilling a square hole??

#13

Re: Drilling a square hole??

RSC Furnishing Design

>Mortisers are good for only 1 thing they drill square holes!

RSC Design