Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

PC BN200 Brad Nailer

Posts

PC BN200 Brad Nailer

#1

PC BN200 Brad Nailer

WarrenC

>I've owned a Porter Cable BN200 Brad Nailer for a few years now and maybe have used it to shoot couple of hundred nails . . .not much. I'm kinda afraid to use it 'cause everytime I use it where it really matters, I get a double bang/bounce and the second nail rarely shoots in all the way or the nail misfires and I have just one nail not all the way in. Its a PITA to remove cleanly as the nail usually breaks off.Other times, where I'm just tacking things together quickly, it works fine. What am I doing wrong?. I depress the nose and then press the trigger. FYI, I've used a framing nailer for years with no problem. Is it me or the gun?

Re: PC BN200 Brad Nailer

#2

Re: PC BN200 Brad Nailer

Barry Irby

>Do you oil the gun? I do not have an air line oiler in my shop now and I put about four drops of oil in the gun almost every time I use one. So, if you have not been oiling it, do so and practice.

It sounds like your nerves may be getting the best of you. The gun works well until you are really counting on it and something changes. In spite of what some of us think, the gun is not psychic and can not tell your prized wood and project from a pallet, but YOU can.

Don't adopt death grip and squeeze the trigger as if you trying to strangle a cobra. Play with it a little and see what makes it work so well on scraps. Relaxed but firm grip, even pressure, nice clean trigger pull, whatever. Then do that on your good stuff.

Barry, who owns aobut six mind reading nail guns.

Re: PC BN200 Brad Nailer

#3

Re: PC BN200 Brad Nailer

George@Colonel's Workshop-Havertown PA

>Good Afternoon Warren,

The newest PC 250MR brad gun is the one you want to use. It sences mental conflicts and is programmed for success. The 205MR (mind reader) is the first in a new line of tools which integrate medical science with woodworking. :<) Try not to TRY so hard, Warren. Relax a bit. You'll feel better when it happens.

George

Re: PC BN200 Brad Nailer

#4

Re: PC BN200 Brad Nailer

WarrenC

>I definitely oil the gun. Maybe the gun is haunted. I just can't figure out what I'm doing different.

Re: PC BN200 Brad Nailer

#5

Re: PC BN200 Brad Nailer

Keith Newton

>Sometimes making an improvement in one area, becomes a trade-off in another. Having a safety like these, eliminates the chance of shooting a nail across the room and hitting someone in the eye over there. But having a safety that must be depressed to fire, yet will shoot a second fastener just by bouncing on the safety while the trigger is depressed, can not only cause the problem that you are experiencing, it can lead to sending the second one into your finger.

You can do one of two things. First press the gun harder into the work, so it won't bounce away. The second choice is to cut a little block of wood that jambs into that little space between the top of the magazine and the bottom of that metal part which connects the trigger to the tip. It should be about the size of a sugar cube. This will allow the gun to shoot anytime you pull the trigger, so you need to be careful with that, but it is not the same hazard that a framing gun would be.

Re: PC BN200 Brad Nailer

#6

Re: PC BN200 Brad Nailer

Glenn Madsen near San Francisco

>My copy of that gun is what blew out a brad sideways from the wood I was fastening, and through one of my fingers. Hit the fingernail from the inside.

I chose to blame the gun, rather than the inattentive operator. You'll appreciate why, I'm certain.

Re: PC BN200 Brad Nailer

#7

Re: PC BN200 Brad Nailer

Bill White

>Have you got it set to "bump fire", or will it only work in single fire mode? What psi are you using at the gun?

Bill

Re: PC BN200 Brad Nailer

#8

Re: PC BN200 Brad Nailer

Keith Newton

>Bill, I don't know if you are asking me the question, or the OP.

With the little block in, there is no safety, so you must pull the trigger to fire for each brad, which takes care of the double firing.

Re: PC BN200 Brad Nailer

#9

I had the same problem - fixed now

Derek

>The gun came with a bump fire trigger installed ant I had the same problem.

I had to call up Porter Cable and get the single-shot (I think it was called sequential fire) trigger. Replacement was easy and the part was free.