>In Shop Shot #847, we feature the last in a series of recent submissions from Alan Young. Alan was kind enough to provide us with this exclusive look at his corbel project. I'd like to thank him for this, as I know the temptation to post these on the messageboards first is hard to resist. Again, Alan did a beautiful job of documenting his work as he went along. There are a few steps he missed photos of but he supplied me with some words explaining what he did - the rest I just made up!!
Now, I know this is a great looking project, but come on, surely some of you have some feedback or questions you'd like to offer. Don't be shy - this is your chance to say what's on your mind - good, bad, or indifferent. I know Alan is thick-skinned enough to handle any critique and would be all too happy to answer all your questions as well. So have at it folks.
>I looked at the shop shot of Alan's project. You want the truth? You can't handle the truth!!!
The truth is that Alan's shop is VERY dusty. He obviously used a lot of clamps just to show off. And that shot of him looking so intently as he worked? Come on! That's an obvious pose glamour shot.
Ok...so the corbels came out fantastic and he did a great job. But the rest of it seems to go a little too far to glamorize what professional woodworking is all about. Trust me...it's not all that pretty!
>I think you're right about the glamor shot, Tom. It must be the thespian in him. Even though he hasn't played a woodworker on TV, he certainly gives a dazzling performance in the shop!
>In your text you didn't say and I just couldn't make up anything good myself, so - when you routed out the waste on the corbel sides with your plunge router and straight bit, how did you keep the base of the router level over the entire length with little support as you head toward the bottom?
One trick I could think of would be to attach the router to a larger base plate and place two corbels back to back to allow two fairly parallel edges for the base to ride on.
>Glamor and Alan =oxymoron Glamor is the oxy and I'm the moron
BTW in the future I hope to be able to accomplish finishes like this Faux job....I've hired some new help for painting....His name is "Ambrose"--claims to have had some stage experience-built some sets and did a two step....I found him down at the local shelter. He was holding a sign that said "will scrape paint for food" ...
I put him to work on some bookcases.... we'll see how he works out...
I hope he's not giving me some song and dance just to earn some Ramon Noodles....
Where can you get a taxidermied cat for a prop? (Lower right corner of the first picture.) I need one to draw the eye away from some of my work, before I allow any photos.
And, I can't tell you how happy the sawdust on top of the DC hose on the bandsaw makes me. I feel better about my whole home made DC system. This is an honest picture. Some of you guys are liars. You clean for a week before you take a picture and not again for a year.
When I grow up, I want to be able to do work like that.
>In your text you didn't say and I just couldn't make up anything good myself, so - when you routed out the waste on the corbel sides with your plunge router and straight bit, how did you keep the base of the router level over the entire length with little support as you head toward the bottom?
One trick I could think of would be to attach the router to a larger base plate and place two corbels back to back to allow two fairly parallel edges for the base to ride on.
So, how did you do it?
Nice work!
David
Hi David,
I think the lower end was actually the easier part....I just did my best to keep the router flat to the available surface...I was able to rout from both directions-So I started with placing the router on the surface that later received the glued on rosette...There was enough room to "pivot" the router to get the material romoved...as I moved up the corbel from bottom to top I just swung the router in a series of short arc's keeping it as flat as possible.... any discrepancies caused by the router "dipping" too far into the waste area were scraped and sanded away later.....