Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

My benches, and a couple of new spoons *PICS*

Posts

My benches, and a couple of new spoons *PICS*

#1

My benches, and a couple of new spoons *PICS*

Mike Schwing from Maryland

>A few months ago I received a lot of great help here with suggestions on building my own benches for a basement workshop. Here they are. The benches were made with 2x4s, all mortise/tenon'd and thru bolted. 2 layers of 3/4 plywood and then the 5/8" thick solid beech countertops from IKEA were screwed on top. The drawers are homemade with slides from Grizzly and cherry faces. The bench tops are framed out with 2" thick oak and all finished with a couple of coats of Watco. The backsplashes are curly maple. I like them a lot, and they're built at a height for me! (which is too short for anyone else)

The spoon/fork set are new. They are made from bleached holly finished with water based lacquer. I was able to preserve the blank I cut them from and is pictured below as well. The spoon set is already sold (yea!) and I will be making a mahogany mount for them. The spoons are about 22" long. Tell ya what, its not easy carving a spindle by hand and keeping it straight. Gave me a new respect for guys who do it with spokeshaves. All comments welcome.




Re: My benches, and a couple of new spoons *PICS*

#2

I have shop envy......

Barry Irby

>You have tile in your shop and Dave Tenney has an area rung and a helper. I have a rough concrete slab with twenty five years of spilled paint and glue.

Good looking spoons. A little more utilitarian looking than most? There appears to be at least one more hiding in that blank, between the other two. (speaking of utility.)

Re: My benches, and a couple of new spoons *PICS*

#3

Re: My benches, and a couple of new spoons *PICS*

George@Colonel's Workshop-Havertown PA

>Wow Mike,

Nice benches. Contrary to the shop layout, they most certainly don't look like "L". I like the beech and may adapt your idea when I rebuild my own counter tops, which are sad and sore. Oh, like the spoons, too.

The benches ought to have a shop shot location.

George

Re: My benches, and a couple of new spoons *PICS*

#4

Steven Antonucci

Was your shop in Better Homes and Gardens?

steve antonucci

>Mine didn't look that clean even before I moved into it. I'm betting that you sit there and clean as you go. Sand, sand, sand, vacuum, vacuum, vacuum, sand...

Likr the fork and spoon set too. That way I can give everyone their salad from my end of the table ;-)

S

Re: My benches, and a couple of new spoons *PICS*

#5

Paul Kramer

The benches are very nice

Paul Kramer

>Mike,

For that matter so are the utensils. I priced the Ikea counter tops but shipping was the killer. Material cost: $60.00. Shipping cost $243.00. Just couldn't justify it. Maybe it's not so much if I pick it up at one of their stores. But there are none close-by

Paul

Re: My benches, and a couple of new spoons *PICS*

#6

Re: Was your shop in Better Homes and Gardens?

Wayne

>I cleaned my bench once but for the life of me I couldn't figure out what to do with the stuff in the tray, I shrugged my shoulders a couple of times and vaccuumed around it. I sweep up and vac when I have run out of things to do. My wife comes in and rolls her eyes and shakes her head and goes back into the house. Our house looks like this shop. Reaslly it would be nice to have mine that clean.

Re: My benches, and a couple of new spoons *PICS*

#7

Re: Was your shop in Better Homes and Gardens?

Mike Schwing from Maryland

>Anyone that knows me well knows that I'm fanatical about clean. In the middle of a project, all hell breaks loose, everything is everywhere. But after every project is completed, a total clean up occurs. I spent several hours this morning cleaning both "shops" (the garage counts, too) You got to see it clean! Thanks for all the nice comments.

Re: My benches, and a couple of new spoons *PICS*

#8

that tile floor

Mike Schwing from Maryland

>Funny story. I contemplated for months over what I was going to put down for my shop floor - I closed off part of the basement and made it my shop, but it was carpeted. I went back and forth with all sorts of ideas before finally realizing my paralysis was keeping me from starting. I decided to just rip up the carpet and work on bare concrete floor till I figured things out.

So I ripped up the carpet and that nice tile was underneath the whole time!!!!! How about that!

Re: My benches, and a couple of new spoons *PICS*

#9

Bench height

wilbur

>Nice job on the benches!

I'm also vertically challenged, and in the process of building a bench. If you don't mind, how tall are you, how tall are your benches, and how did you come up with your final bench height?

Re: My benches, and a couple of new spoons *PICS*

#10

Re: Bench height

Carol Reed - Dubuque, IA (temporarily)

>I'm short, too, and have badly injured my back in an auto accident, so height became critical if I was to wood work at all.

I got a helper to measure me. I stood straight with my arms bent at the elbows and clasping my hands together. My helper measured from the bottom of my elbd to the floor. Subtracted 4" to accommodate workpieces and tools. Made the bench that height. It turned out to be quite comfortable. I don't have to slightly bend over which I simply cannot do without pain.

Why not try to adjust the height of any table to whatever your number is with above method, and see how it feels standing at with a tool in your hands?

Re: My benches, and a couple of new spoons *PICS*

#11

The Shop Gods smiled !

SteveM

>