Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

OK - time for a splitter

Posts

OK - time for a splitter

#1

OK - time for a splitter

Dave Bonde - Iowa

>Last night I had a kickback while cutting a 36"X18" piece of 1/2 � MDF in half. I currently do not have a splitter but that is about to change. My question is what splitter have you used that you really like. I have a Powermatic P66 and use the saw often for cutting dados so would want a splitter that can be easily removed. Am I better off with a commercial setup like the Biesemeyer (or other) or should I make one. Thanks for your thoughts. Dave

Re: OK - time for a splitter

#2

Re: OK - time for a splitter

Bob Entwisle in NJ

>I have been using a Merlin splitter on my Unisaw for a couple of years now. It pops on and off easily, which means that I put it on whenever it's appropriate.

Re: OK - time for a splitter

#3

Re: Biesemeyer - Goodall

Al Stokka - Cambridge, Iowa

>Dave,

I have the Biesemeyer removable splitter and it's a pleasure to use. Easy to install and remove (just pull a spring-loaded pin). That means one is more likely to use the thing.

Mark Goodall has (I think) the Delta part number on his web site. Much cheaper than buying it as an add-on kit.

Al

Re: OK - time for a splitter

#4

Re: OK - time for a splitter

Neal in San Jose

>For a very low cost, quick solution, I added a splitter to my home-made plywood zero clearance insert. I had some 1/8 ply left over from a project and cut a small piece about 1 inch square. I cut a kerf in a new insert exactly behind the blade opening and glued it in. I made mine about 5/8 high, but you could make it any size you need; even make multiples in different heights. I found I needed to lightly sand the splitter so it didn't drag on the stock as it went by, and it limited me to using full kerf blades, but changing from the splitter to no splitter was simply a matter of changing the insert.

Re: OK - time for a splitter

#5

Bart Goldberg

I have the Beis - And I would buy again!

Bart Goldberg

>

Re: OK - time for a splitter

#6

Re: OK - time for a splitter

Larry Clinton

>I have the Microjig splitter. This mounts directly to you saw insert. I have had very good results using this and have purchased a second set for extra inserts. This comes with a set of plastic inserts (splitters) that allows you to put in a "straight" splitter which works like a normal splitter. Another splitter is offset (I think .003") to hold the board against the fence. I have pulled the splitter out of the saw insert on a couple of occasions when working with reaction wood. In every case the splitter remained in the board saw cut ~ no kickback. a couple weeks ago I was ripping some aromatic red cedar, had two boards which closed on the splitter hard enough I couldn't force the board though the cut. I had to shut down the saw and wedge the saw cut open to remove the splitter and insert from the board. I was using Grr-Rippers at the same time and had no problems. I also believe the Grr-Rippers are also a big part of preventing kickback. I just replaced the legs on both of my Grr-Rippers. If I ever lose one I will buy another the same day.

Re: OK - time for a splitter

#7

THANKS! + Question for Al

Dave Bonde - Iowa

>Thanks for the great information guys and a question for Al or anybody that might know. I have a Powermatic PM66 Al said Mark G. has a Delta part number that is less expensive. If I decide to go with the Biesemeyer I am guessing that Delta part number will not work for my Powermatic is that correct?. Thanks again Dave

Re: OK - time for a splitter

#8

Jim DeLaney, Austintown, Ohio

Re: OK - time for a splitter

Jim DeLaney, Austintown, Ohio

>I tried the Microjig splitter - pulled out of the insert on the first pinch and wouldn't ever stay in place after that. Trashed it.

I then tried the Delta UniGuard splitter. I liked it, but it was too thin - really best used with a thin kerf blade.

I finally bit the bullet and bought the Biesemeyer splitter. This one is great. The only time it ever comes off the saw is for dadoes and non-thru cuts. It's a keeper!

Jim D.

Re: OK - time for a splitter

#9

Re: Mark G.? John Weber?

Al Stokka - Cambridge, Iowa

>Dave,

Diggin through Mark G's website and my Badger Pond Archives CD, here's what I find:

BP Archives, by Mark G., July 1, 1999:

"The Uniguard splitter is black and uses a big thumb screw, so you must lift the throat plate to insert AND remove. The Biesemeyer is a little fancier, it's silver with some white paint, and it can click in without removeing the throat plate, but you must still lift it to get at the spring loaded knob to remove the splitter."

"The Biesemeyer splitter is a better splitter (plus there are 11+ models so it might fit a PM saw for instance), but $29 compared to $109 the Uniguard splitter is a better deal."

BP Archives, by Mark G., July 2, 1999:

Uniguard splitter: "part number: 1349941 SPLITTER ASSY COMPLETE"

BP Archives, by John Weber, July 1, 1999:

"I have the Uniguard for my Powermatic 66. I modified the splitter to work on the left-tilt PM, and used the standard PM hardward to bolt it in place. It's easy to remove with a wrench I keep in the guard basket. Best of Luck with your new PM 64."

I have the Beisemeyer splitter. I particularly like the ease with which it can be installed and removed with a sprin-loaded pin. The Uniguard splitter, I find, requires loosening a thumbscrew to install/remove the splitter, but then, the Uniguard spliter is cheaper (through Delta parts department) so I guess you have a decision to make.

Hopefully John and Mark will jump in here.

Al

Re: OK - time for a splitter

#10

Re: Biesemeyer splitter

Al Stokka - Cambridge, Iowa

>Dave,

I found a web page for the Biesemeyer spliiter, should you want to take a look at it. This one is for a left-tilt Unisaw (right-tilt available):

http://www.biesemeyer.com/Products/AccessoriesDetail.aspx?ProductID=13723

Re: OK - time for a splitter

#11

Re: Biesemeyer splitter

Dave Bonde - Iowa

>Thanks Al - I think I am going with the biesemeyer. I don't trust myself if I have to screw/unscrew it to use the Delta, I guess I am willing to pay for the convenience at this point. Dave

Re: OK - time for a splitter

#12

another option, sharkguard!

arw01

>These are truly loved by all that have one, and is on my shop safety improvement lists for the over the blade dust collection.

Personally I use a MG Splitter in a phenolic insert. That little bugger is STILL a bear to remove. I suspect that people with MG's that pop out are not using commercial throat plates.

A few times I've had wood close up so tight I had to turn off the saw, back it up and make the same cut again to widen out the kerf.

Alan


img

Re: OK - time for a splitter

#13

Re: Goodall - Delta

Mark Mandell - Gone Round In Jersey

>Jeez, Al, talk about memories! I used Mark's posted info from our Pond days to fit the Delta to my left-tilt JET cab.

Has worked very well, and is always installed except for dado cuts.

mm

Re: OK - time for a splitter

#14

Re: another option, sharkguard!

Jay St. Peter - SoMD

>I currently have the Delta splitter (otherwise known as the Goodall splitter). I've been checking out the Shark guard for a while. I'll get it eventually to replace my overhead blade guard. This looks a lot less annoying. I use the splitter often, but the overhead guard is usually over in the corner.

Jay

Re: OK - time for a splitter

#15

I'll second that

Larry Marker in Alabama

>I have both the MicroJig splitter and a couple Grr-Rippers and I wouldn't be without either. I have the Delta Delux Uniguard overarm guard which comes with a removable splitter that isn't quite a nice as the Boes, but is still pretty good. Ever since I got the MicroJig splitter and the Grr-Rippers, I haven't had either the Iniguard or its splitter on the saw.

Larry

Re: OK - time for a splitter

#16

Re: OK - time for a splitter

Kevin Rabenaldt

>You were cutting mdf and had a kickback? Kickbacks usually occur when ripping solid wood and the wood "moves" behind the blade and pinches the wood against a fence. I had a few kickbacks before I installed a commerical fence and keeps the fence parallel to the blade. Since then (20 years) I have not had another kickback. I am careful what I cut and if the wood "moves" after a few inches of cutting, I stop.

Sheet goods should not kickback on you if you feed the material in correctly.

Kevin

Re: OK - time for a splitter

#17

Badger Pond Archives CD

Dan Mitchell

>Al-Is this archive available online anyplace? I've searched and can't find it.

TIA

Dan

Re: OK - time for a splitter

#18

Re: Badger Pond Archives CD

Ron Hildreth, Alta, Iowa

>Dan,

On the left of this page you'll see "BP Articles & Reviews". What you're looking for should be in there!

Ron in Iowa

Re: OK - time for a splitter

#19

Installing or Removing is Pretty Easy....

Scott in Eastern Iowa

>....if you have < than 15 seconds it can be done rather easily.

And its about 1/3 the price of the snap in that was mentioned.

ps...Ive got it installed on my Uni...tis a pleasure to use.

Re: OK - time for a splitter

#20

Re: Badger Pond Archives CD

Dan Mitchell

>Thanks Ron. I had looked at that, but the search engine doesn't seem to work. Tried a number of terms, even just "wood", keep getting a NOT FOUND message. I was looking for an archive of the old forum, rather than articles on specific topics.

Dan

Re: OK - time for a splitter

#21

Re: OK - time for a splitter

Michael Wangler in Rochester, NY

>Mine is similar to Neal's Here is a picture.


img

Re: OK - time for a splitter

#22

Re: Andrew Field's Badger Pond Archives CD

Al Stokka - Cambridge, Iowa

>Dan,

Sorry for the delayed response. I didn't see your post until just now.

About the Badge Pond Archives CD. Andrew Field created the CD (with Wayne Miller's permission and blessing. There is a hyper link on the CD's opening page: http://www.winisp.net/a_field/badgerpond.html but, I have not been able to access the site. Perhaps Andrew closed it down? Perhaps someone here kept in touch with Andrew and can fill us both in on his and the CD's status. I's be willing to have my son copy my CD (I wouldn't have the slightest idea how to do that. oh yeah, Al? Then why'd you pay extra for a CD burner in your computer? and send it to you if I were sure it isn't copyrighted. Anyone know? Dan, wanna send me your snail mail address while we're waiting for info on the CD?

Sophie was a buddy of Andrews, I seem to recall. To bad Sophie's too busy for is old pals. He he, just kidding Sophie.

Al