Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

bandsaw blade guides

Posts

bandsaw blade guides

#1

bandsaw blade guides

Carol - now in NC Nebraska

>I got a used Delta 9" benchtop bandsaw while I am on internship to help make chunks round to feed the mini lathe. I have it all cleaned up and new Timberwolf on it.

Now I need some blade guides. The old olds are barely usable. They appear to be 1/4" square pieces of black plastic. (Maybe a phenolic?) Of course that is a size that Cool Blocks DON'T come in!

So, replacement material. I'd like to get something that is already 1/4" square as I have no safe way to make something that size while I am here.

Any thoughts on plastics? I can order something from U.S. Plastics if need be. Delrin? Teflon?

Hobby Lobby has square brass. Would that work?

I know a really dense hardwood, oily, like rosewood would work, but I don't have any and getting something like that where I am is wishful thinking.

Need to get creative here. Any thoughts?

Re: bandsaw blade guides

#2

Re: bandsaw blade guides

David Charters

>how about a #2 pencil?

Re: bandsaw blade guides

#3

Re: bandsaw blade guides *LINK*

JimM

>Carol,

Page 1802 of MSC Big Book online, bottom right - 1/4 x 2 ft square bar (Delrin) Acetal # 63386403 price $3.89.

I expect the shipping would be more than the bar.


MSC Industrial Supply

Re: bandsaw blade guides

#4

Re: bandsaw blade guides

Brian Hahn in SW Wisconsin

>I would avoid any type of thermoplastic like Delrin, nylon, Teflon, etc. The friction will soften and/or melt them and then you will have a real mess. Thermoset plastics like phenolics are OK because they won't soften or melt in this application.

My suggestions are: Dogwood or hard maple if you want to use a wood for the blocks. If you want metal block, I would use cold rolled steel. The original guide blocks on my Delta 14" were steel and they worked quite well.

Re: bandsaw blade guides

#5

Re: bandsaw blade guides

JohnKJordan in East TN

>Carol,

I can imagine teflon would be too soft and perhaps hard to hold in place with the set screws. Many plastics will melt with the heat of friction.

I'd probably try the square brass rod.

And just wondering - will the UHMW polyethylene stock that Woodcraft, for example, sells for jigs and fixtures work or would it soften too much with friction? (I found references that said the melting point was 230-275F with a continuous service temperature of 160-180F.) This stuff is self lubricating and very tough, used for gears, bearings, wear surfaces, conveyer parts, etc. You could cut pieces from some 1/4" stock with the bandsaw.

Also, it seems to me if you have a store like Woodcraft nearby, they might be willing to cut or sand down some Cool Blocks to fit for you.

JKJ

Re: bandsaw blade guides

#6

Re: bandsaw blade guides

Carol - now in NC Nebraska

>Thanks, but Woodcraft is in another state from me! Hobby Lobby is 3 hours away in Norfolk, NE. There is also a Menard's there. Sioux City, IA is 5 hours away. There is a Harbor Freight there! Whodda thunk? But I digress.

I get to Norfolk about once a month, so that is the handiest. In fact, I should be there next Wednesday. I can get the brass stock at Menard's and perhaps also Hobby Lobby. Glad to know that should work. But Cool Blocks would be better. Sighhh...

The only saw I have here (besides the bandsaw) is a Makita SCMS. Not good for making 1/4" square stock. And retaining the ability to count to ten in whole numbers on my fingers!

Slow but sure the shop is coming together for turning. The grinder is now set up but no wheel guards yet. I stripped down a very old Craftsman with super bearings, but 6" wheels. I put it on a little pedestal and put on 8" wheels, so I have to fabricate some guards. That probably won't happen until I get home next summer!

So far, the Nebraska woodworkers around here are still in hiding. Haven't flushed any out yet. Workin' on it.

Re: bandsaw blade guides

#7

Re: bandsaw blade guides

Clay Foster

>I bet somewhere in Nebraska is some Osage Orange (bois d'arc, hedge apple, horse apple). Even an old fence post would provide enough material for guide blocks. It's been used for house piers, paving blocks, and even plow shares. Your current band saw and a sharp knife should get it cut close enough.

Re: bandsaw blade guides

#8

Re: bandsaw blade guides

Carol - now in NC Nebraska

>Thanks, Clay.

I'll ask around.

Re: bandsaw blade guides

#9

Osage orange

Virgil Johnson

>I have enough Osage orange to make some guides for you. Email me the dimensions and a mailing address. This will give me an excuse to cut wood for a change.

Re: bandsaw blade guides

#10

Me too..........

Barry Irby

>I have a number of woods that might suffice. If Virgil doesn't come through for you, let me know. I might have Kingwood, a derivative of Rosewood and I also have Osage. And, in winter I can see Lowes from my house. I could pick up some brass or steel and cut it and send it to you. I also have a slightly used set of cool blocks I could cut down for you, if somebody will "esplain" to me what to cut them with.

Re: bandsaw blade guides

#11

Here's What I Use  *LINK*

George (Oxford, NC)

>


Home Made Cool Blocks

Re: bandsaw blade guides

#12

Re: Here's What I Use

Carol - now in NC Nebraska

>Cool, George. (Pardon the pun.)

I had seen that but didn't remember it. Duh!

My guides are square, but if I use wood, your suggestion is that I present end grain to the blade (as a dowel would) treated as you did. Good idea. Right now my problem is still getting them cut.

I think I might try one of finer tooth blades that came with it and try to cut something out of hardwood.

Thanks for the help.

Re: bandsaw blade guides

#13

Gosh, guys...

Carol - now in NC Nebraska

>you are all terrific!

I'll get out and accurately measure what is there and get back to you.

Right now I need to go meet with a lady whose husband passed three hours ago.

Later.

Re: bandsaw blade guides

#14

Carol.......

Ron Hildreth, Alta, Iowa

>Hope we didn't accidently chase you out of Iowa!

Ron in Iowa

Re: bandsaw blade guides

#15

Don't forget locust.

Jim Dillon

>

Re: bandsaw blade guides

#16

Re: Carol.......

Carol - now in NC Nebraska

>LOL. That's a good one, Ron.

No, you didn't chase me out of Iowa, accidentally or on purpose. I am on internship until the end of next July.

All I brought with me was my mini lathe and a few other things. I bought the little bandsaw off of Ebay. I have a much better Powermatic at home! But this will have to do for now.

Actually I may be closer to you from here than I was in Dubuque. Problem is I don't have weekends off. :) It seems to be traditional that pastors work on Sundays. Hmmm.... wonder how THAT got started. :)

Maybe while you are recooping (sp) from your surgery, you might be available for a during the week visit. I have a friend who now lives in Meservy, IA. She wants me to visit.

Re: bandsaw blade guides

#17

Bandsaw guides measurements

Carol - now in NC Nebraska

>For any and all who offered to help out.

The guides are 15/64's square. An inch long would be more than adequate. Any longer I would likely have to shorten them. There are 4 of them. Mailing address is Box 474, Bassett, NE 68714.

Thanks folks. You are the best!

Re: bandsaw blade guides

#18

White OAK

George@Colonel's Workshop-Havertown PA

>

Re: bandsaw blade guides

#19

Re: Carol.......

Ron Hildreth, Alta, Iowa

>Sounds like a plan! I'll be finding out probably Monday or Tuesday if I'll actually be going under the knife. Just had the MRI this morning. After nearly three months of pain, I'm ready for anything!!

I'll keep ya posted and we can work out details then. I'm planning on making a trip down to Des Moines to the Woodsmith store, and warned Al Stokka that I might be stopping in Cambridge to make sure he's up on his toes, too!

Ron in Iowa

Re: bandsaw blade guides

#20

Shipping might kill this...

Denis Ch�nard, Orl�ans, Ont.

>But a pen blank will provide you like a dozen sets of guides. Like these here:

http://www.leevalley.com/wood/page.aspx?c=2&p=32840&cat=1,250,43217,43221&ap=1

Or, you could use maple, I remember FWW testing them in a comparison with other types of guides, and maple did well.

DC

Re: bandsaw blade guides

#21

Done

Virgil Johnson

>I'll mail 4 Osage Orange (hedge apple) blanks on Monday.

Re: bandsaw blade guides

#22

Re: Done

Carol - now in NC Nebraska

>Thanks, Virgil. You are terrific!

Re: bandsaw blade guides

#23

Me too also.

Barry Irby

>I just made up a few sets for you. Osage orange, Kingwood, purple heart, bamboo, and the gray stinky ones are the remnants of my Cool Blocks that I cut down for you. That stuff is tough and it stinks when cut. I guess the tough part is the point. You may need to sand them a bit to get them into the guides. They did not cut as "purty" as the wood. I'll mail them today or tomorrow.

Re: bandsaw blade guides

#24

Re: Me too also.

Carol - now in NC Nebraska

>Thanks, Barry.

I will have blade guides that will outlast the baby bandsaw.

The generosity of the folks here is absolutely outstanding. I look forward to the day I can meet more of you face to face.

Re: bandsaw blade guides

#25

I guess I'll save the postage.

Virgil Johnson

>Barry made enough for the both of us.