Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

In search of better Epoxy

Posts

In search of better Epoxy

#1

In search of better Epoxy

Ron Bauman

>I've been using local hardware brand name epoxy as a glue and filler. Recently when using as a filler (knots, inclusions, etc.)if I have any depth to fill I noticed fine bubbles in the mix. This ends up looking like a gray blob in the middle of a black knot hole. Until now I never had this problem, I don't mind an amber tinge instead of dead clear, but want to avoid the little effervescences. There's been some Epoxy discussion here from time to time, but I don't remember any chatter about this problem. On the other hand, my memory is starting to slope off to the East now and again. TIA

Re: In search of better Epoxy

#2

Re: In search of better Epoxy *LINK*

Thomas Skaggs, Foothills of Mount Level

>I have good luck with West System epoxies. Here is a link:

Tom


West System

Re: In search of better Epoxy

#3

Re: In search of better Epoxy

Paul Woolson

>West Systems is pretty much the standard in epoxies. You can't go wrong with it.

I'm guessing you bubbles are technique rather than the epoxy itself. You need to make sure that the temperature of the piece is falling as the epoxy cures. In boat building we had to make sure we epoxied in the heat of the day so that it dried as the evening cooled.

One thing you can do is warm the piece before you epoxy it. If size permits, throw it in an oven at 100-150 degrees. Then you'll not have the gassing problems.

Re: In search of better Epoxy

#4

Re: In search of better Epoxy

Larry Clinton

>As this is not a structural application, I use the 5 minute or 1 hour kits from Wally World. The ones with the two barrel syringe. I add black Rit dye to the 2 parts, then mix thoroughly. I have preheated deep knot holes with a hair dryer. Usually I just fill and sand. If any bubbles break and leave a small depression, I just mix up a tiny batch and refill the area. With the black dye - entrapped bubbles can't be seen. After sanding to 220 grit the epoxy has a somewhat dull, grey appearance, but as soon as any finish is applied this becomes a smooth black.

Re: In search of better Epoxy

#5

Re: In search of better Epoxy

Pete in Holland, MI

>Air is induced during the mixing of the exoxy and it is too thick to naturally bubble out.

Do you have a vacuum pump?

Mix up your next batch of epoxy, create a vacuum chamber to allow your mixing container to fit in it and pull a vacuum before your pour. This'll get rid of any air in the mix.

This technique is used in our composites studio for pouring large quantities of urethane, silicone and other 2 part mixtures.

Pete

Re: In search of better Epoxy

#6

Re: In search of better Epoxy

Keith Newton

>Another thing which could have happened, is that if the space that you filled was of a large enough volume, the epoxy can produce enough heat to boil, which produces what you describe.

Rather than using colors, I usually mix the dust from my belt-sander bag into the epoxy as filler. It will usually come out darker than the wood that it came from, even when mixed in with colloidal silica.

Re: In search of better Epoxy

#7

Re: In search of better Epoxy

Bob Sobieck

>I would try Epoxy Heads, Bay City, MI. I think they are advertized in FWW. By coincidence, I travel right past the place for the last 20 years enroute via 500 miles from Green Bay, WI to extreme eastern MI to the inlaws.

I stopped there. They said no one ever stops, only mail order. They have a lot of literature on their products and even asked if I wanted to talk to some of their chemical engineers. These people are serious about expoxy. Get their publishings - I learned a lot and for things I never would have thought.

I did buy some and have been very satisfied. I hate to admit but I am one of those peoople who reaches for the epoxy befre the duct tape.

Bob

Re: In search of better Epoxy

#8

Re: In search of better Epoxy

Scott Banbury

>The bubbles could be coming from mixing or just from deep down in the crack or knot hole you're filling. Either way they can be coaxed to the surface before the epoxy cures by sweeping a heat gun 6-8" above the surface.

Re: In search of better Epoxy

#9

Re: In search of better Epoxy

del schisler

>i poured lot's of epoxy What you need to do is use a small flame a torch flame on the poured area after probly 10 mim you will see the bubles break and go to a mix that has no bubbles (or real shinny) You can do this again in say 1/2 hr and do it again their will be a few bubbles show up DONT GET TO CLOSE IT WILL BOIL just close enough look across the mix You will see the bubbles disapear They also make a bubble breaker in a spray also I have poured 100's of cypress clocks yrs ago and lot's of other item's