Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Deft

Posts

Deft

#1

Deft

Randy Johnson Connersville, IN

>I recently bought some Deft lacquer to try as a finish on bowls.

The directions say not to thin it and they also mention light coats. With the can I have, applying a "light" coat is impossible. It's like brushing on honey. Actually the first coat isn't all that bad. It isn't like shellac, but it does more or less flow on. After the first coat, the brush drags. Even 24 hours after the previous application it acts like I would expect if I was trying to apply it too soon between coats. Because of the drag I'm having to put way too much on to not have areas that are missed.

The directions also say it can't be sprayed or I would try the hvlp.

I've tried different brushes thinking that might help. It didn't.

Did I luck out and just buy a can of the stuff that for whatever reason is too thick? (doubtful) Or, is there something about applying this product that I am simply missing? (likely)

I'm ready to give the sawdust/shavings pile a real nice finish and go back to slower but easier methods like shellac and oil.

Re: Deft

#2

Suggestion

Robert R Clough - Thorncraft

>In similar situations I brushed first and then, having had an experience as did you, I went with Deft spray. So far it has worked.

Re: Deft

#3

Re: Deft

Bill Roland (Mt Juliet,TN)

>I just looked at a can I have in the shop and it does not give a specific time between coats or any experation date. I used it several years ago and put multible coats on some cabinets and had no problems. It looks like you may have a problem with your product, maybe it was exposed to and extreme temperature. I don't know if that would effect it or not.

My 2 cents.

Re: Deft

#4

Thin it; anything can be thinned

Clint Searl, at the base of Haycock Mtn

>If you have spray equipment, try Sherwin Williams solvent based alkyd lacquer.

Clint

Re: Deft

#5

Re: Deft

Roger

>Randy,

Cut it with a 50% mixture of lacquer thinner, it should meter out if a paint gauge in about 14 seconds. I spray the consecutive coats when it is dry to the touch (about 15 minuets). Make sure the weather is not too hot or to cold or you will have trouble with bubbling (too hot and air escaping from the grain) or blushing.

Roger

Re: Deft

#6

I've Sprayed Gallons of Deft

Mike Fitterling

>In spite of the can saying "brush on lacquer" you can easily spray Deft. I have sprayed it using my HVLP conversion gun. I usually thin it a bit by adding 1/4 lacquer thinner. I just finished a huge kitchen sprayed with "brushing lacquer."

That said, it can also be brushed successfully. I have done that on smaller projects. Lacquer, like shellac, dissolves any layers of lacquer you are applying it on top of. The key is a quick brush on, with no going back to tip off, just get it covered and leave it. The Deft should level out on its own and it is called "brushing" because there are retarders in it to give it more time to do that levellling off. It is suprising how much it will level off, even after it feels dry to the touch. If you still do not end up with a smooth enough surface, you can rub it out to whatever sheen you want with pumice and/or rottenstone. Probably be unecessary, though.

Good luck,

Mike

Re: Deft

#7

Re: Deft

Rod Peterson -- Ormond Beach

>> …about 15 minuets…

And then, is it Bach to the drawing board?

Had to get in there before the Colonel.

Rod

Re: Deft

#8

Re: Deftly Composed, Rod

George@Colonel's Workshop-Havertown PA

>

Re: Deft

#9

thinning, more from CA government

Bill Tindall, E.TN

>The reason that cans of stuff say "don't thin" is because they have formulated to pass state's (that would be CA) air standards for solvents. (There is some rule on quantity of VOC's per gallon.) If it was thinned so it would work properly it would not pass. Any solvent formulated material can be thinned with a compatible solvent to aid flow out or film build. Just don't tell anyone you are doing it.

Thinning water based finish is not as straightforward.

Re: Deft

#10

Re: Deft

Ron Hildreth, Alta, Iowa

>Man, you guys just opened yourselves up to "Woodworker's Journal e-zine typo corner!! Big time!!

Ron in Iowa

Re: Deft

#11

Nothing wrong with your Deft!

Lee Schierer - McKean, PA

>Your Deft is acting normal. It is different than other finishes in that it will very rapidly soften the layer underneath as it is applied. The trick is heavy second and third coats, basically lay it on as even as you can and don't try to go back over areas that were already coated. It will dry to re-coat in 30 minutes in hot dry weather and it can used at temps as cold as you can stand to work. I personally have applied Deft at 20 degrees F. and have had no problems. It gives off toxic fumes so be sure to apply it in a well ventilated space. In cold weather you may have to wait 12 hours or more for it to dry. I do my winter finishing in an unheated garage in NW PA. Sand after the first coat with 220, make sure you wipe and or vacuum off all the dust. After the second coat rub out with 0000 steel wool. You can apply paste wax after the final coat, again with 0000 steel wool.

One final note. Deft doesn't yellow much with age so you can "clean up a finish many years later with a quick rubdown with steel wool and a recoat. The new coating will bond and become part of the previous finish layers.

Deft is also available in spray cans so it can be thinned.

Lee

P.S. Where did you find yours?? Most of my local sources have dried up?

Re: Deft

#12

One Thing

David Yoho

>Since Deft is billed as a "brushing" lacquer, they add something (lacquer thinner perhaps) to allow it to flow out when using a brush without drying as fast as standard lacquer would.

I've sprayed it before with my HVLP turbine unit with some success. However, I didn't like the fumes and cleaning the gun when done. I tried a water-based lacquer (CrystaLac) later and found it a much more user friendly product for spraying with my HVLP rig with great results.

David

Re: Deft

#13

Only one of us…

Rod Peterson -- Ormond Beach

>Plays on words aren't typos (unless I missed a typo made while playing).

Rod

Re: Deft

#14

Re: Only one of us�

Ron Hildreth, Alta, Iowa

>Yea, I know, Rod, but they do those, too!

Ron in Iwa

Re: Deft

#15

Lee----

Ron Hildreth, Alta, Iowa

>Lee,

You mentioned NW Pa. How far from North East (the town) are you?

The reason I ask, years ago I drove truck long distance for a company near here that was owned by Wooster Trucklines, of North East, Pa. The wife and I went through there on our way to Boston a few years ago. Thought I'd stop in the old company to see if I might still know anyone, and was VERY suprised that they had gone belly up the year before! Man, that was a big fleet - having terminals in about nine states and hauling as far west as South Dakota!

Ron in Iowa

Re: Deft

#16

Re: Nothing wrong with your Deft!

Randy Johnson Connersville, IN

>P.S. Where did you find yours?? Most of my local sources have dried up?

Gee, I really wish you hadn't asked that but since you did......

.....Wal Mart. It's the only place I could find it.

Re: Deft

#17

Thanks everyone. What I have learned.....

Randy Johnson Connersville, IN

>First and foremost, in this case anyway, the directions on the can seem to be something less than 100% accurate. Not only can it be thinned, it can be sprayed and at lower temperatures than indicated by the maker.

I'll try the hlvp with what I have left while I can still spray outside and then go back to other methods until warm weather rolls around again.

I've also learned that my proofreading skills ain't what they used to be.

I had to read Roger's post a couple of times before I saw what Rod was refering to.

Re: Deft

#18

Not Lee, but…

Rod Peterson -- Ormond Beach

>> …Wooster Trucklines, of North East, Pa.

I have my own ties there. I am originally from Jamestown, NY, which is only 25 or 30 miles from North East. In fact, my uncle and his family, who all “got religion” back in the '60s, had gone from one church to another in the Jamestown area looking for a congregation and pastor they liked and finally settled on one in North East.

It was the better part of a Sunday for them to get six kids all fed and organized and out the door for an hour's drive to church. Nowadays, with I-86 available from I-90 at North East, and going right through Chautauqua County and past Jamestown, it's probably not over 20 minutes or so to get there, but back in the day, with nothing but two lanes over those hills and through the three or four one-horsers, it was nearly an hour.

I have another cousin there who has driven OTR for a Pennsylvania outfit called NBS Trucking. Stands for No BS (no kidding).

Lee is south of Erie—less than 20 miles, I think. North East is—are you ready for it?—northeast of Erie. Lee can tell you how many minutes in his Miata.

Rod

Re: Deft

#19

I am Lee,�

Lee Schierer - McKean, PA

>Northeast (all one word) is about 20-25 minutes from my house in Mckean (about 7 miles south of Erie) via the interstates in a Miata....but generally we prefer the back roads to the intersate when driving the Miata.

Lee

Re: Deft

#20

Re: Deft

Don Bullock

>Did you sand between coats? If you didn't that would cause your problem.